Toyota Wheel Fitment Guide

253 fitment guides for Toyota, covering 1983 to 2027, spanning 4x100, 5x100, 5x108, 5x112, 5x114.3, 5x120, 5x150 and 6x139.7 bolt patterns. Browse the full list below, then open a model for bolt pattern, center bore, OE offset, flush and max wheel sizes, and offset/backspacing conversions.

Run a Toyota club, forum or blog? Add our free bolt pattern and center bore lookup to your site, set to open on Toyota only. Get the free embed code →

Toyota Bolt Pattern & Center Bore Notes

Based on the 253 Toyota fitment guides we cover, we have documented 11 distinct bolt pattern / center bore combinations across different Toyota platforms and model years:

  • 5x114.3 bolt pattern, 60.1mm center bore — 114 models we cover, spanning 1983–2027.
  • 4x100 bolt pattern, 54.1mm center bore — 38 models we cover, spanning 1999–2026.
  • 6x139.7 bolt pattern, 106.1mm center bore — 31 models we cover, spanning 2003–2027.
  • 5x100 bolt pattern, 54.1mm center bore — 20 models we cover, spanning 1992–2019.
  • 5x150 bolt pattern, 110.1mm center bore — 15 models we cover, spanning 2003–2026.
  • 6x139.7 bolt pattern, 95.1mm center bore — 11 models we cover, spanning 2022–2027.
  • 5x100 bolt pattern, 56.1mm center bore — 9 models we cover, spanning 2012–2026.
  • 5x120 bolt pattern, 60.1mm center bore — 5 models we cover, spanning 2018–2024.
  • 5x112 bolt pattern, 66.6mm center bore — 4 models we cover, spanning 2020–2026.
  • 6x139.7 bolt pattern, 95.2mm center bore — 4 models we cover, spanning 2022–2026.
  • 5x108 bolt pattern, 65.1mm center bore — 2 models we cover, spanning 2016–2020.

Do not mix platforms: a wheel forged for one Toyota bolt pattern / center bore combination will not hub-center correctly on a different one, even if the diameter looks right. Always confirm your exact model and year against the bolt pattern and center bore listed on that model page below before ordering — or send us your VIN or trim level and we will confirm it for you.

Offset and backspacing recommendations vary by trim even within the same bolt pattern, mainly due to differences in brake caliper size and suspension geometry between base and performance trims. Every ANKUSI wheel is forged to your exact target offset, so send us your Toyota model, year, and trim and we will confirm the correct spec before production — no guessing required.

How to check the bolt pattern on your Toyota

The most common Toyota fitment in our guide is 5x114.3 with a 60.1 mm center bore (114 of 253 model years we cover).

  1. Read the stamping on the back of an original wheel: size, offset (ET) and bolt pattern are usually cast into a spoke or the hub pad.
  2. No stamping? Measure center-to-center between two adjacent lug holes. For 5x114.3 that distance is 67.2 mm (PCD × sin(180° / 5)). A 2 mm difference already means a different bolt pattern.
  3. Match generation and year on the model pages below — the same nameplate can change bolt pattern or center bore between generations.

Changing width or offset? Check how far the wheel moves in or out with our offset & backspacing calculator.

5x114.3 / 60.1mm center bore

4x100 / 54.1mm center bore

6x139.7 / 106.1mm center bore

Forged Wheels for Toyota

Forged-to-order wheel designs matched to Toyota bolt patterns. Every set is machined to your exact model, offset and center bore.

Vehicles Using 5x114.3 With a 60.1 mm Center Bore

In our database, 138 other vehicle entries from 18 makes use exactly the same 5x114.3 bolt pattern and 60.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.

5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 16.8% of those also use a 60.1 mm center bore.

Hub-Centric Rings for a 60.1 mm Center Bore

A wheel with a center bore larger than 60.1 mm needs a hub-centric ring. The most common combinations:

Wheel boreRing size
63.4 mm63.4 → 60.1 mm
64.1 mm64.1 → 60.1 mm
65.1 mm65.1 → 60.1 mm
66.1 mm66.1 → 60.1 mm
73.1 mm73.1 → 60.1 mm

ANKUSI forged wheels are bored to exactly 60.1 mm for this vehicle, so no ring is needed.

Sources and Last Update

Bolt pattern and center bore were checked against at least two independent fitment references before publication.

This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).

Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.

← Back to the full Fitment Guide · Browse forged wheels

Contact WhatsApp Get a Quote