
Matte Gold 5 V-Spoke Forged Wheels
Monoblock · Matte Gold
Fitting Toyota GT86 TRD wheels? This page gives the 2014 Toyota GT86 TRD bolt pattern (5x100), centre bore, factory rim size and the offset range for aftermarket and forged Toyota GT86 TRD rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Toyota GT86 — styles, sizes & factory quote →
Toyota GT86 TRD (2014): 5x100 bolt pattern, 56.1mm center bore. Factory wheels: F/R: 18x7.5J at ET48 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 18x7.5J F/R |
| Flush Fitment | 18x8.5J at ET35 offset |
| Maximum Aggressive | 19x8.5J at ET30 offset |
Every design below is forged to order, so it can be machined to the Toyota GT86 TRD's 5x100 bolt pattern and 56.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Matte Gold

Monoblock · Transparent Copper

Monoblock · Gunmetal

Replica · Champagne Gold

Monoblock · Satin Black

Replica · Gunmetal

Replica · Metallic Gray / Gray

Replica · Matte Silver
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a performance-oriented coupe, the wheel is one of the few components where shaving weight has a compounding effect — less rotational mass means less work for the brakes, the drivetrain, and the chassis on every input. A forged wheel gets there without compromising the strength margin the factory engineered in.
The Toyota GT86 TRD runs a 5x100 bolt pattern, 56.1mm center bore, and a 18x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x8.5J ET35, which tucks the tire under the fender lip on a stock-height Toyota GT86 TRD. Our Maximum Aggressive reference is 19x8.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2014 Toyota GT86 TRD (Sport Coupe) uses a 5x100 bolt pattern with a 56.1mm center bore. Factory wheels are F/R: 18x7.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota GT86 TRD (2014) we drill the 5x100 pattern and cut the centre bore to 56.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota GT86 TRD? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.