
Toyota OEM-Style Matte Silver 6-Spoke Forged Wheels
Replica · Matte Silver
Fitting Toyota Avensis wheels? This page gives the 2003 Toyota Avensis bolt pattern (5x100), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Avensis rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Toyota Avensis — styles, sizes & factory quote →
Toyota Avensis (2003): 5x100 bolt pattern, 54.1mm center bore. Factory wheels: F/R: 15x6.0J at ET45 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 15x6.0J F/R |
| Flush Fitment | 16x7.0J at ET38 offset |
| Maximum Aggressive | 17x7.5J at ET35 offset |
Every design below is forged to order, so it can be machined to the Toyota Avensis's 5x100 bolt pattern and 54.1 mm center bore, with the width and offset calculated for your setup.

Replica · Matte Silver

Replica · Silver

Monoblock · Gunmetal

Replica · Champagne Gold

Replica · Gunmetal

Monoblock · Matte Gold

Monoblock · Satin Black

Monoblock · Transparent Copper
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


A wagon carries wagon-specific weight distribution — more mass over the rear axle when loaded — so wheel strength at the rear corners matters as much as the front. Forging lets us match the factory's strength target on both ends while keeping rotational mass down, which keeps the ride composed whether the cargo area is empty or full.
The Toyota Avensis runs a 5x100 bolt pattern, 54.1mm center bore, and a 15x6.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 16x7.0J ET38, which tucks the tire under the fender lip on a stock-height Toyota Avensis. Our Maximum Aggressive reference is 17x7.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2003 Toyota Avensis (Sedan/Wagon) uses a 5x100 bolt pattern with a 54.1mm center bore. Factory wheels are F/R: 15x6.0J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Avensis (2003) we drill the 5x100 pattern and cut the centre bore to 54.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Avensis? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.