Bright Silver Full-Face Forged Wheels
Monoblock · Bright Silver
2007 Toyota Corolla Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Toyota Corolla wheels? This page gives the 2007 Toyota Corolla bolt pattern (5x100), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Corolla rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Toyota Corolla (2007): 5x100 bolt pattern, 54.1mm center bore. Factory wheels: F/R: 15x6.0J at ET39 offset, front and rear. Reference fitment ranges.
Bolt Pattern5x100
Wheel Bolt/NutM12x1.5 Nut
Center Bore54.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2007
CategoryCompact Sedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 15x6.0J F/R |
| Flush Fitment | 16x7.0J at ET38 offset |
| Maximum Aggressive | 17x7.5J at ET35 offset |
Forged Wheel Designs for the Toyota Corolla
Every design below is forged to order, so it can be machined to the Toyota Corolla's 5x100 bolt pattern and 54.1 mm center bore, with the width and offset calculated for your setup.
Advan Racing GT-Style Bright Gray 6-Spoke Deep Lip Forged Wheels
Deep Dish · Bright Gray
APEX VS-5RS-Style Matte Silver Forged Wheels
Replica · Matte Silver
BBS RE-V7-Style Gunmetal 7 Y-Spoke Forged Wheels
Replica · Gunmetal
Advan Racing Bright Silver 6-Spoke Forged Wheels
Replica · Bright Silver
Schmidt-Style Gloss Black 7 Y-Spoke Machined Lip Forged Wheels
Monoblock · Gloss Black
Platinum Brushed Bright Silver 5 Y-Spoke Forged Wheels
Monoblock · Brushed Bright Silver
APEX-Style Brushed Silver 5 Split-Spoke Forged Wheels
Replica · Matte Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Toyota Corolla runs a 5x100 bolt pattern, 54.1mm center bore, and a 15x6.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 16x7.0J ET38, which tucks the tire under the fender lip on a stock-height Toyota Corolla. Our Maximum Aggressive reference is 17x7.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Toyota Corolla OE Wheel Specs
The 2007 Toyota Corolla (Compact Sedan) uses a 5x100 bolt pattern with a 54.1mm center bore. Factory wheels are F/R: 15x6.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Corolla (2007) we drill the 5x100 pattern and cut the centre bore to 54.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F/R: 15x6.0J ET39 → ~5.04″ backspacing
- Flush: 16x7.0J ET38 → ~5.5″ backspacing
- Max: 17x7.5J ET35 → ~5.63″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Corolla? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Toyota Corolla use?
The 2007 Toyota Corolla uses a 5x100 bolt pattern.
How many lug bolts does the Toyota Corolla use?
The Toyota Corolla uses a 5-lug bolt pattern (5x100), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Toyota Corolla?
The Toyota Corolla's center bore is 54.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Toyota Corolla?
Factory wheels on the Toyota Corolla are F/R: 15x6.0J F/R.
What is the biggest wheel size I can fit on my Toyota Corolla without rubbing?
The most aggressive fitment we recommend without fender work is 17x7.5J at ET35 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Toyota Corolla?
For a flush look with minimal to no rubbing, we recommend 16x7.0J at ET38 offset as a starting point on a stock or mildly lowered Toyota Corolla.
Do I need wheel spacers for my Toyota Corolla?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Toyota Corolla?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.5" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Toyota Corolla?
The Toyota Corolla runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.