
2010 Toyota iQ3 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Toyota iQ3 wheels? This page gives the 2010 Toyota iQ3 bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Toyota iQ3 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Toyota iQ3 (2010): 4x100 bolt pattern, 54.1mm center bore. Factory wheels: F/R: 15x5.0J at ET39 offset, front and rear. Reference fitment ranges.
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 15x5.0J F/R |
| Flush Fitment | 15x6.0J at ET30 offset |
| Maximum Aggressive | 16x6.5J at ET25 offset |
Forged Wheel Designs for the Toyota iQ3
Every design below is forged to order, so it can be machined to the Toyota iQ3's 4x100 bolt pattern and 54.1 mm center bore, with the width and offset calculated for your setup.


BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold

Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White

BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal

BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold

OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White

Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold

Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Toyota iQ3 runs a 4x100 bolt pattern, 54.1mm center bore, and a 15x5.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 15x6.0J ET30, which tucks the tire under the fender lip on a stock-height Toyota iQ3. Our Maximum Aggressive reference is 16x6.5J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Toyota iQ3 OE Wheel Specs
The 2010 Toyota iQ3 (Micro Car) uses a 4x100 bolt pattern with a 54.1mm center bore. Factory wheels are F/R: 15x5.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota iQ3 (2010) we drill the 4x100 pattern and cut the centre bore to 54.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F/R: 15x5.0J ET39 → ~4.54″ backspacing
- Flush: 15x6.0J ET30 → ~4.68″ backspacing
- Max: 16x6.5J ET25 → ~4.73″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota iQ3? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Toyota iQ3 use?
How many lug bolts does the Toyota iQ3 use?
What is the center bore size on the Toyota iQ3?
What size are the factory (stock) wheels on the Toyota iQ3?
What is the biggest wheel size I can fit on my Toyota iQ3 without rubbing?
What does a flush wheel fitment look like on the Toyota iQ3?
Do I need wheel spacers for my Toyota iQ3?
How do I calculate wheel backspacing for my Toyota iQ3?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Toyota iQ3?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.