
2010 Toyota Prius Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Toyota Prius wheels? This page gives the 2010 Toyota Prius bolt pattern (5x100), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Prius rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Toyota Prius (2010): 5x100 bolt pattern, 54.1mm center bore. Factory wheels: F/R: 15x6.5J at ET45 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 15x6.5J F/R |
| Flush Fitment | 16x7.0J at ET38 offset |
| Maximum Aggressive | 17x7.5J at ET35 offset |
Forged Wheel Designs for the Toyota Prius
Every design below is forged to order, so it can be machined to the Toyota Prius's 5x100 bolt pattern and 54.1 mm center bore, with the width and offset calculated for your setup.


Rays Volk Racing TE37-Style Gloss Black 6-Spoke Racing Forged Wheels
Replica · Gloss Black

Toyota OEM-Style Matte Silver 6-Spoke Forged Wheels
Replica · Matte Silver

Matte Silver 12-Spoke Forged Wheels
Monoblock · Matte Silver

Rays-Style Gloss Black 5-Spoke Forged Wheels
Replica · Gloss Black

Metallic Gray 5 Y-Spoke Concave Forged Wheels
Concave · Metallic Gray

Gunmetal 9-Spoke Forged Wheels
Monoblock · Gunmetal

Gloss Black 5 Y-Split-Spoke Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The Toyota Prius runs a 5x100 bolt pattern, 54.1mm center bore, and a 15x6.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 16x7.0J ET38, which tucks the tire under the fender lip on a stock-height Toyota Prius. Our Maximum Aggressive reference is 17x7.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Toyota Prius OE Wheel Specs
The 2010 Toyota Prius (Hybrid Liftback) uses a 5x100 bolt pattern with a 54.1mm center bore. Factory wheels are F/R: 15x6.5J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Prius (2010) we drill the 5x100 pattern and cut the centre bore to 54.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F/R: 15x6.5J ET45 → ~5.52″ backspacing
- Flush: 16x7.0J ET38 → ~5.5″ backspacing
- Max: 17x7.5J ET35 → ~5.63″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Prius? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Toyota Prius use?
How many lug bolts does the Toyota Prius use?
What is the center bore size on the Toyota Prius?
What size are the factory (stock) wheels on the Toyota Prius?
What is the biggest wheel size I can fit on my Toyota Prius without rubbing?
What does a flush wheel fitment look like on the Toyota Prius?
Do I need wheel spacers for my Toyota Prius?
How do I calculate wheel backspacing for my Toyota Prius?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Toyota Prius?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.