Rays Volk Racing TE37-Style Gunmetal Forged Wheels
Replica · Gunmetal
2019 Toyota Corolla Hatchback Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Toyota Corolla Hatchback wheels? This page gives the 2019 Toyota Corolla Hatchback bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Corolla Hatchback rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Toyota Corolla Hatchback (2019): 5x114.3 bolt pattern, 60.1mm center bore. Factory wheels: F/R: 16x7.0J at ET40 offset, front and rear. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore60.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2019
CategoryHatchback
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 16x7.0J F/R |
| Flush Fitment | 18x8.0J at ET38 offset |
| Maximum Aggressive | 19x8.5J at ET35 offset |
Forged Wheel Designs for the Toyota Corolla Hatchback
Every design below is forged to order, so it can be machined to the Toyota Corolla Hatchback's 5x114.3 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.
Rays-Style Bronze 12-Spoke Forged Wheels
Replica · Bronze
Toyota OEM-Style Gloss Black Machined Turbine Multi-Spoke Forged Wheels
Monoblock · Gloss Black / Machined
Rays-Style Satin Black 6-Spoke Forged Wheels
Monoblock · Satin Black
Bronze Double 5-Spoke Forged Wheels
Replica · Bronze
Gloss Black Split Y-Spoke Mesh Forged Wheels
Monoblock · Gloss Black
Rays Volk Racing TE37-Style Gloss White 6-Spoke Racing Forged Wheels
Replica · Gloss White
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The Toyota Corolla Hatchback runs a 5x114.3 bolt pattern, 60.1mm center bore, and a 16x7.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x8.0J ET38, which tucks the tire under the fender lip on a stock-height Toyota Corolla Hatchback. Our Maximum Aggressive reference is 19x8.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Toyota Corolla Hatchback OE Wheel Specs
The 2019 Toyota Corolla Hatchback (Hatchback) uses a 5x114.3 bolt pattern with a 60.1mm center bore. Factory wheels are F/R: 16x7.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Corolla Hatchback (2019) we drill the 5x114.3 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F/R: 16x7.0J ET40 → ~5.57″ backspacing
- Flush: 18x8.0J ET38 → ~6″ backspacing
- Max: 19x8.5J ET35 → ~6.13″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Corolla Hatchback? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Toyota Corolla Hatchback use?
The 2019 Toyota Corolla Hatchback uses a 5x114.3 bolt pattern.
How many lug bolts does the Toyota Corolla Hatchback use?
The Toyota Corolla Hatchback uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Toyota Corolla Hatchback?
The Toyota Corolla Hatchback's center bore is 60.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Toyota Corolla Hatchback?
Factory wheels on the Toyota Corolla Hatchback are F/R: 16x7.0J F/R.
What is the biggest wheel size I can fit on my Toyota Corolla Hatchback without rubbing?
The most aggressive fitment we recommend without fender work is 19x8.5J at ET35 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Toyota Corolla Hatchback?
For a flush look with minimal to no rubbing, we recommend 18x8.0J at ET38 offset as a starting point on a stock or mildly lowered Toyota Corolla Hatchback.
Do I need wheel spacers for my Toyota Corolla Hatchback?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Toyota Corolla Hatchback?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Toyota Corolla Hatchback?
The Toyota Corolla Hatchback runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.