BBS RE-V7-Style Metallic Gray 12-Spoke Forged Wheels
Replica · Metallic Gray
1985 Toyota Supra Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Toyota Supra wheels? This page gives the 1985 Toyota Supra bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Supra rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 1985 Toyota Supra uses a 5x114.3 bolt pattern with a 60.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 14x6.0J ET22, front and rear. For aftermarket wheels, 15x7.0J ET12 sits flush and 16x7.5J ET5 is the most aggressive fit.
Forged wheels for the 1985 Toyota Supra — drilled 5x114.3 with a 60.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Toyota Supra (1985): 5x114.3 bolt pattern, 60.1mm center bore. Factory wheels: F/R: 14x6.0J at ET22 offset, front and rear. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore60.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year1985
CategorySport Liftback
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 14x6.0J F/R |
| Flush Fitment | 15x7.0J at ET12 offset |
| Maximum Aggressive | 16x7.5J at ET5 offset |
Forged Wheel Designs for the Toyota Supra
Every design below is forged to order, so it can be machined to the Toyota Supra's 5x114.3 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.
HRE-Style 2-Piece Satin Black 5 Y-Spoke Riveted Gunmetal Lip Forged Wheels
2-Piece · Satin Black
Toyota OEM-Style Gloss Black Machined Split Multi-Spoke Forged Wheels
Monoblock · Gloss Black / Machined
Toyota OEM-Style Matte Black 12-Spoke Off-Road Forged Wheels
Off-Road · Matte Black
Work-Style Chrome 6-Spoke 2-Piece Deep Lip Forged Wheels
2-Piece · Chrome
Rays-Style Gloss Bronze Deep Lip Forged Wheels
Deep Dish · Gloss Bronze
Rays-Style Gunmetal Mesh Polished-Lip Forged Wheels
Deep Dish · Gunmetal
Gloss White 10-Spoke Forged Wheels
Monoblock · Gloss White
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The Toyota Supra runs a 5x114.3 bolt pattern, 60.1mm center bore, and a 14x6.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 15x7.0J ET12, which tucks the tire under the fender lip on a stock-height Toyota Supra. Our Maximum Aggressive reference is 16x7.5J ET5 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Toyota Supra OE Wheel Specs
The 1985 Toyota Supra (Sport Liftback) uses a 5x114.3 bolt pattern with a 60.1mm center bore. Factory wheels are F/R: 14x6.0J F/R.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Supra (1985) we drill the 5x114.3 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Supra? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Toyota Supra: Specs by Model Year
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 14x6J | ET22 | 4.37 in (111 mm) | — | — |
| Flush | 15x7J | ET12 | 4.47 in (114 mm) | +3 mm | +23 mm |
| Maximum | 16x7.5J | ET5 | 4.45 in (113 mm) | +2 mm | +36 mm |
Vehicles With the Same Hub as the Toyota Supra (5x114.3, 60.1 mm Bore)
In our database, 214 other vehicle entries from 19 makes use exactly the same 5x114.3 bolt pattern and 60.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 16.8% of those also use a 60.1 mm center bore.
Hub-Centric Rings for a 60.1 mm Center Bore
A wheel with a center bore larger than 60.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 63.4 mm | 63.4 → 60.1 mm |
| 64.1 mm | 64.1 → 60.1 mm |
| 65.1 mm | 65.1 → 60.1 mm |
| 66.1 mm | 66.1 → 60.1 mm |
| 73.1 mm | 73.1 → 60.1 mm |
ANKUSI forged wheels are bored to exactly 60.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Toyota Supra use?
The 1985 Toyota Supra uses a 5x114.3 bolt pattern.
How many lug bolts does the Toyota Supra use?
The Toyota Supra uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Toyota Supra?
The Toyota Supra's center bore is 60.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Toyota Supra?
Factory wheels on the Toyota Supra are F/R: 14x6.0J F/R.
What is the biggest wheel size I can fit on my Toyota Supra without rubbing?
The most aggressive fitment we recommend without fender work is 16x7.5J at ET5 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Toyota Supra?
For a flush look with minimal to no rubbing, we recommend 15x7.0J at ET12 offset as a starting point on a stock or mildly lowered Toyota Supra.
Do I need wheel spacers for my Toyota Supra?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Toyota Supra?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 4.47" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Toyota Supra?
The Toyota Supra runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 14x6 wheels · 14 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.