
APEX VS-5RS-Style Black Chrome Forged Wheels
Replica · Black Chrome
Fitting Toyota Grand Highlander Platinum wheels? This page gives the 2024 Toyota Grand Highlander Platinum bolt pattern (5x120), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Grand Highlander Platinum rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Toyota Grand Highlander — styles, sizes & factory quote →
Toyota Grand Highlander Platinum (2024): 5x120 bolt pattern, 60.1mm center bore. OE F/R: 20x7.5J ET35 F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 20x7.5J F/R |
| Flush Fitment | 20x8.5J at ET38 offset |
| Maximum Aggressive | 21x9.0J at ET35 offset |
Every design below is forged to order, so it can be machined to the Toyota Grand Highlander Platinum's 5x120 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.

Replica · Black Chrome

Replica · Light Gray

Replica · Bronze Gold

Concave · Chrome

Monoblock · Bright Silver

Monoblock · Bright Silver

Deep Dish · Gloss Black

Replica · White
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Toyota Grand Highlander Platinum runs a 5x120 bolt pattern, 60.1mm center bore, and a 20x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x8.5J ET38, which tucks the tire under the fender lip on a stock-height Toyota Grand Highlander Platinum. Our Maximum Aggressive reference is 21x9.0J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2024 Toyota Grand Highlander Platinum (3-Row SUV) uses a 5x120 bolt pattern with a 60.1mm center bore. Factory wheels are F/R: 20x7.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Grand Highlander Platinum (2024) we drill the 5x120 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Grand Highlander Platinum? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.