2026 Toyota HiLux BEV Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Toyota HiLux BEV wheels? This page gives the 2026 Toyota HiLux BEV bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Toyota HiLux BEV rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2026 Toyota HiLux BEV uses a 6x139.7 bolt pattern with a 106.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 17x7.5J ET30. For aftermarket wheels, 18x8J ET25 sits flush.
Forged wheels for the 2026 Toyota HiLux BEV — drilled 6x139.7 with a 106.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Toyota HiLux BEV (2026): 6x139.7 bolt pattern, 106.1mm center bore, OE 17x7.5J ET30. Forged wheel fitment specs from ANKUSI.
Bolt Pattern6x139.7
Wheel Bolt/NutM12x1.5 Nut
Center Bore106.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2026
Category6-Lug Off-Road (Beadlock)
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x7.5J ET30 |
| Flush Fitment | 18x8J at ET25 offset |
Forged Wheel Designs for the Toyota HiLux BEV
Every design below is forged to order, so it can be machined to the Toyota HiLux BEV's 6x139.7 bolt pattern and 106.1 mm center bore, with the width and offset calculated for your setup.
Mirror Polished 20-Spoke Beadlock Forged Wheels
Off-Road Beadlock · Polished
Rays-Style Gloss Black 5-Spoke Off-Road Forged Wheels
Off-Road · Gloss Black
Rays-Style Gloss Black 6-Spoke Off-Road Forged Wheels
Off-Road · Gloss Black
Rays-Style Matte Black Custom Off-Road Forged Wheels
Off-Road · Matte Black
Fuel-Style Matte Black Offset-Spoke Bolt Ring Beadlock Off-Road Forged Wheels
Off-Road Beadlock · Matte Black
KMC-Style Matte Black 5-Spoke Bolt-Ring Off-Road Forged Wheels
Off-Road · Matte Black
Gloss Black Mesh Beadlock Forged Wheels
Off-Road Beadlock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Off-road platforms put real, repeated impact loads through the wheel that street-only vehicles never see, so the factory strength margin on the Toyota HiLux BEV isn't a formality — it's load-bearing in a literal sense. Forging matches that margin at a lower rotational weight than an equivalent cast wheel, which matters both on the trail and on the highway miles between trailheads.
The Toyota HiLux BEV ships from the factory on a 6x139.7 bolt pattern with a 106.1mm center bore and a 17x7.5J ET30 wheel. Our flush reference for the Toyota HiLux BEV is 18x8J ET25.; our maximum aggressive reference is 20x9J ET20. — beyond that, expect clearance issues against the fender liner without further modification.
Toyota HiLux BEV OE Wheel Specs
The Toyota HiLux BEV ships from the factory on 6x139.7 bolt pattern wheels with a 106.1mm center bore. The stock wheel size is 17x7.5J ET30, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota HiLux BEV (2026) we drill the 6x139.7 pattern and cut the centre bore to 106.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 17x7.5J | ET30 | 5.43 in (138 mm) | — | — |
| Flush | 18x8J | ET25 | 5.48 in (139 mm) | +1 mm | +11 mm |
| Maximum | 20x9J | ET20 | 5.79 in (147 mm) | +9 mm | +29 mm |
Vehicles With the Same Hub as the Toyota HiLux BEV (6x139.7, 106.1 mm Bore)
In our database, 32 other vehicle entries from 7 makes use exactly the same 6x139.7 bolt pattern and 106.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
6x139.7 is used by 4.0% of the vehicle pages in our English fitment guide (258 of 6,503); 12.8% of those also use a 106.1 mm center bore.
Hub-Centric Rings for a 106.1 mm Center Bore
A wheel with a center bore larger than 106.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 108.1 mm | 108.1 → 106.1 mm |
| 110.1 mm | 110.1 → 106.1 mm |
| 130.1 mm | 130.1 → 106.1 mm |
ANKUSI forged wheels are bored to exactly 106.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Toyota HiLux BEV use?
The 2026 Toyota HiLux BEV uses a 6x139.7 bolt pattern.
How many lug bolts does the Toyota HiLux BEV use?
The Toyota HiLux BEV uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Toyota HiLux BEV?
The Toyota HiLux BEV's center bore is 106.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Toyota HiLux BEV?
Factory wheels on the Toyota HiLux BEV are 17x7.5J ET30.
What does a flush wheel fitment look like on the Toyota HiLux BEV?
For a flush look with minimal to no rubbing, we recommend 18x8J at ET25 offset as a starting point on a stock or mildly lowered Toyota HiLux BEV.
Do I need wheel spacers for my Toyota HiLux BEV?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Toyota HiLux BEV?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.48" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Toyota HiLux BEV?
The Toyota HiLux BEV runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 17x7.5 wheels · 17 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.