
2015 Toyota 4Runner TRD Pro Series Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Toyota 4Runner TRD Pro Series wheels? This page gives the 2015 Toyota 4Runner TRD Pro Series bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Toyota 4Runner TRD Pro Series rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Toyota 4Runner — styles, sizes & factory quote →
Toyota 4Runner TRD Pro Series (2015): 6x139.7 bolt pattern, 106.1mm center bore. OE F/R: 17x7.5J ET15 F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 17x7.5J F/R |
| Flush Fitment | 17x8.5J at ET0 offset |
| Maximum Aggressive | 18x9.0J at ET-5 offset |
Forged Wheel Designs for the Toyota 4Runner TRD Pro Series
Every design below is forged to order, so it can be machined to the Toyota 4Runner TRD Pro Series's 6x139.7 bolt pattern and 106.1 mm center bore, with the width and offset calculated for your setup.


American Force Polished Multi-Spoke Wheels
H-Type · Polished

DT Forge Pink & Chrome Multi-Spoke Wheels
H-Type · Pink / Chrome

KG1 Forged Radar Polished Forged Wheels
H-Type · Polished

MMX Design Polished 5-Spoke Forged Wheels
H-Type · Polished
See all Toyota 4Runner wheel designs Black Mud-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
The Toyota 4Runner TRD Pro Series's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Toyota 4Runner TRD Pro Series runs a 6x139.7 bolt pattern, 106.1mm center bore, and a 17x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x8.5J ET0, which tucks the tire under the fender lip on a stock-height Toyota 4Runner TRD Pro Series. Our Maximum Aggressive reference is 18x9.0J ET-5 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Toyota 4Runner TRD Pro Series OE Wheel Specs
The 2015 Toyota 4Runner TRD Pro Series (Rugged SUV) uses a 6x139.7 bolt pattern with a 106.1mm center bore. Factory wheels are F/R: 17x7.5J F/R.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota 4Runner TRD Pro Series (2015) we drill the 6x139.7 pattern and cut the centre bore to 106.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F/R: 17x7.5J ET15 → ~4.84″ backspacing
- Flush: 17x8.5J ET0 → ~4.75″ backspacing
- Max: 18x9.0J ET-5 → ~4.8″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota 4Runner TRD Pro Series? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Toyota 4Runner TRD Pro Series use?
How many lug bolts does the Toyota 4Runner TRD Pro Series use?
What is the center bore size on the Toyota 4Runner TRD Pro Series?
What size are the factory (stock) wheels on the Toyota 4Runner TRD Pro Series?
What is the biggest wheel size I can fit on my Toyota 4Runner TRD Pro Series without rubbing?
What does a flush wheel fitment look like on the Toyota 4Runner TRD Pro Series?
Do I need wheel spacers for my Toyota 4Runner TRD Pro Series?
How do I calculate wheel backspacing for my Toyota 4Runner TRD Pro Series?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Toyota 4Runner TRD Pro Series?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 103-110 Nm (76-81 ft-lb). Range covers most Toyota passenger cars, crossovers, and light trucks on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.