
Rays Volk Racing TE37-Style Gunmetal 6-Spoke Machined Lip Forged Wheels
Replica · Gunmetal
Fitting Toyota bZ3 wheels? This page gives the 2024 Toyota bZ3 bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Toyota bZ3 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Toyota bZ3 (2024): 5x114.3 bolt pattern, 60.1mm center bore. Factory wheels: F/R: 18x7.5J at ET40 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 18x7.5J F/R |
| Flush Fitment | 19x8.0J at ET38 offset |
| Maximum Aggressive | 20x8.5J at ET35 offset |
Every design below is forged to order, so it can be machined to the Toyota bZ3's 5x114.3 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.

Replica · Gunmetal

Monoblock · Brushed Silver

Monoblock · Gold

2-Piece · Satin Black

Monoblock · Bright Silver

Monoblock · Bright Silver

Monoblock · Bronze

Monoblock · Mirror Polished
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


The Toyota bZ3's factory wheel spec reflects a deliberate balance between comfort, steering feel and durability that the engineering team tuned for. Forging lets ANKUSI match that same strength target while trimming rotational mass — the part of a wheel upgrade that actually changes how the car drives, not just how it looks.
The Toyota bZ3 runs a 5x114.3 bolt pattern, 60.1mm center bore, and a 18x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.0J ET38, which tucks the tire under the fender lip on a stock-height Toyota bZ3. Our Maximum Aggressive reference is 20x8.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2024 Toyota bZ3 (Electric Sedan) uses a 5x114.3 bolt pattern with a 60.1mm center bore. Factory wheels are F/R: 18x7.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota bZ3 (2024) we drill the 5x114.3 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota bZ3? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.