
Brox Metallic Gray Exposed Bolt Detail Deep Lip Forged Wheels
Deep Dish · Metallic Gray
Fitting Toyota Tundra TRD Sport wheels? This page gives the 2018 Toyota Tundra TRD Sport bolt pattern (5x150), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Tundra TRD Sport rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Toyota Tundra — styles, sizes & factory quote →
Toyota Tundra TRD Sport (2018): 5x150 bolt pattern, 110.1mm center bore. Factory wheels: F/R: 20x8.0J at ET60 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 20x8.0J F/R |
| Flush Fitment | 20x9.0J at ET40 offset |
| Maximum Aggressive | 22x9.5J at ET35 offset |
Every design below is forged to order, so it can be machined to the Toyota Tundra TRD Sport's 5x150 bolt pattern and 110.1 mm center bore, with the width and offset calculated for your setup.

Deep Dish · Metallic Gray

Deep Dish · Matte Black

Replica · Gloss Black

Replica · Metallic Gray

Replica · Custom Finish

Deep Dish · Matte Black

Deep Dish · Gloss White

Deep Dish · Gunmetal
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a truck platform, wheel weight sits right at the unsprung mass budget the suspension engineers already spent on payload and towing capacity. A forged wheel keeps that budget intact — same strength, less rotational inertia — instead of eating into the margin the way a cheap cast aftermarket wheel can.
The Toyota Tundra TRD Sport runs a 5x150 bolt pattern, 110.1mm center bore, and a 20x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x9.0J ET40, which tucks the tire under the fender lip on a stock-height Toyota Tundra TRD Sport. Our Maximum Aggressive reference is 22x9.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2018 Toyota Tundra TRD Sport (Pickup) uses a 5x150 bolt pattern with a 110.1mm center bore. Factory wheels are F/R: 20x8.0J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Tundra TRD Sport (2018) we drill the 5x150 pattern and cut the centre bore to 110.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Tundra TRD Sport? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.