
Gunmetal Deep Lip Forged Wheels
Deep Dish · Gunmetal
Fitting Toyota Tundra TRD Pro wheels? This page gives the 2019 Toyota Tundra TRD Pro bolt pattern (5x150), centre bore, factory rim size and the offset range for aftermarket and forged Toyota Tundra TRD Pro rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Toyota Tundra — styles, sizes & factory quote →
Toyota Tundra TRD Pro (2019): 5x150 bolt pattern, 110.1mm center bore. Factory wheels: F/R: 18x8.0J at ET60 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F/R: 18x8.0J F/R |
| Flush Fitment | 18x9.0J at ET35 offset |
| Maximum Aggressive | 20x9.5J at ET30 offset |
Every design below is forged to order, so it can be machined to the Toyota Tundra TRD Pro's 5x150 bolt pattern and 110.1 mm center bore, with the width and offset calculated for your setup.

Deep Dish · Gunmetal

Deep Dish · Matte Black

Replica · Metallic Gray

Replica · Gloss Black

H-Type · Polished

Replica · Matte Black

Deep Dish · Polished

Deep Dish · Matte Black
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


Payload and towing figures on a truck are engineered around a specific unsprung mass budget at each corner. Forging lets ANKUSI hit the factory strength rating for the Toyota Tundra TRD Pro at a lower rotational weight than an equivalent cast wheel, which is the more meaningful upgrade on a work-capable platform than diameter alone.
The Toyota Tundra TRD Pro runs a 5x150 bolt pattern, 110.1mm center bore, and a 18x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x9.0J ET35, which tucks the tire under the fender lip on a stock-height Toyota Tundra TRD Pro. Our Maximum Aggressive reference is 20x9.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2019 Toyota Tundra TRD Pro (Full-Size Pickup) uses a 5x150 bolt pattern with a 110.1mm center bore. Factory wheels are F/R: 18x8.0J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Toyota Tundra TRD Pro (2019) we drill the 5x150 pattern and cut the centre bore to 110.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Toyota spec, or want a wheel built to a custom offset for your Toyota Tundra TRD Pro? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.