Daihatsu Grand Move (1999) Wheel Fitment
Daihatsu Grand Move (1999): 4x100 bolt pattern, 54.1mm center bore. Factory wheels: 14x5.0J F/R. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 14x5.0J F/R |
| Flush Fitment | 15x6.0J at ET32 offset |
| Maximum Aggressive | 16x6.5J at ET30 offset |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Minivans carry passengers and cargo across a wide range of loaded conditions, so the factory wheel spec is built around a conservative load margin. Forging lets us hold that same margin while trimming rotational mass, which shows up as smoother ride quality whether the vehicle is empty or fully loaded.
The Daihatsu Grand Move runs a 4x100 bolt pattern, 54.1mm center bore, and a 14x5.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 15x6.0J ET32, which tucks the tire under the fender lip on a stock-height Daihatsu Grand Move. Our Maximum Aggressive reference is 16x6.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Daihatsu Grand Move OE Wheel Specs
The 1999 Daihatsu Grand Move (MPV) uses a 4x100 bolt pattern with a 54.1mm center bore. Factory wheels are 14x5.0J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
Flush Fitment
For a flush look with minimal rubbing, F/R 15x6.0J ET32 is the recommended starting point on a stock or mildly lowered Daihatsu Grand Move.
Maximum Aggressive Fitment
F/R 16x6.5J ET30 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 14x5.0J ET38
Recommended setup: 14x5.0J ET38 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade 15x5.5J ET35
Recommended setup: 15x5.5J ET35 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 15x6.0J ET32
Recommended setup: 15x6.0J ET32 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 16x6.5J ET31
Recommended setup: 16x6.5J ET31 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 16x6.5J ET30
Recommended setup: 16x6.5J ET30 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 14x5.0J ET38 | 15x5.5J ET35 | 15x6.0J ET32 | 16x6.5J ET31 | 16x6.5J ET30 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 14x5.0J ET38
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 15x6.0J ET32
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 16x6.5J ET30
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 14x5.0J ET38 → ~4.5″ backspacing
- Flush: 15x6.0J ET32 → ~4.76″ backspacing
- Max: 16x6.5J ET30 → ~4.93″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Daihatsu spec, or want a wheel built to a custom offset for your Daihatsu Grand Move? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.