BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
1997 Daihatsu Cuore Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Daihatsu Cuore wheels? This page gives the 1997 Daihatsu Cuore bolt pattern (4x110), centre bore, factory rim size and the offset range for aftermarket and forged Daihatsu Cuore rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 1997 Daihatsu Cuore uses a 4x110 bolt pattern with a 66.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 12x4.0J, front and rear. For aftermarket wheels, 13x5.0J ET35 sits flush and 14x5.5J ET35 is the most aggressive fit.
Forged wheels for the 1997 Daihatsu Cuore — drilled 4x110 with a 66.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Daihatsu Cuore (1997): 4x110 bolt pattern, 66.1mm center bore. Factory wheels: 12x4.0J F/R. Reference fitment ranges.
Bolt Pattern4x110
Wheel Bolt/NutM12x1.5 Nut
Center Bore66.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year1997
CategoryHatchback
Data check: published sources disagree on part of this vehicle's hub data, and we are reviewing it. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 12x4.0J F/R |
| Flush Fitment | 13x5.0J at ET35 offset |
| Maximum Aggressive | 14x5.5J at ET35 offset |
Forged Wheel Designs for the Daihatsu Cuore
Every design below is forged to order, so it can be machined to the Daihatsu Cuore's 4x110 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.
Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White
BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold
BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold
Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold
OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Hot hatches and performance compacts are built around quick direction changes, so rotational mass at the wheel has an outsized effect on how the car actually feels to drive. Forging trims that mass while holding the same strength margin as the factory wheel, which is exactly the trade-off this kind of platform rewards.
The Daihatsu Cuore runs a 4x110 bolt pattern, 66.1mm center bore, and a 12x4.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 13x5.0J ET35, which tucks the tire under the fender lip on a stock-height Daihatsu Cuore. Our Maximum Aggressive reference is 14x5.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Daihatsu Cuore OE Wheel Specs
The 1997 Daihatsu Cuore (Hatchback) uses a 4x110 bolt pattern with a 66.1mm center bore. Factory wheels are 12x4.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Daihatsu Cuore (1997) we drill the 4x110 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 12x4.0J ET40 → ~4.07″ backspacing
- Flush: 13x5.0J ET35 → ~4.38″ backspacing
- Max: 14x5.5J ET35 → ~4.63″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Daihatsu spec, or want a wheel built to a custom offset for your Daihatsu Cuore? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Daihatsu Cuore: Specs by Model Year
| Year | Bolt pattern | Center bore | Factory wheel |
|---|---|---|---|
| 1997 | 4x110 | 66.1 mm | 12x4J |
| 2004 | 4x100 | 54.1 mm | 13x4.5J |
Check the model year before ordering: the specs change — bolt pattern 4x110 → 4x100 from 2004; center bore 66.1 mm → 54.1 mm from 2004.
Vehicles With the Same Hub as the Daihatsu Cuore (4x110, 66.1 mm Bore)
In our database, 1 other Daihatsu entries use exactly the same 4x110 bolt pattern and 66.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
4x110 is used by <0.1% of the vehicle pages in our English fitment guide (3 of 6,503); 66.7% of those also use a 66.1 mm center bore.
Hub-Centric Rings for a 66.1 mm Center Bore
A wheel with a center bore larger than 66.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.6 mm | 66.6 → 66.1 mm |
| 67.1 mm | 67.1 → 66.1 mm |
| 70.1 mm | 70.1 → 66.1 mm |
| 70.5 mm | 70.5 → 66.1 mm |
| 73.1 mm | 73.1 → 66.1 mm |
ANKUSI forged wheels are bored to exactly 66.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Daihatsu Cuore use?
The 1997 Daihatsu Cuore uses a 4x110 bolt pattern.
How many lug bolts does the Daihatsu Cuore use?
The Daihatsu Cuore uses a 4-lug bolt pattern (4x110), so you need a 4-lug forged wheel to bolt straight on.
What is the center bore size on the Daihatsu Cuore?
The Daihatsu Cuore's center bore is 66.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Daihatsu Cuore?
Factory wheels on the Daihatsu Cuore are 12x4.0J F/R.
What is the biggest wheel size I can fit on my Daihatsu Cuore without rubbing?
The most aggressive fitment we recommend without fender work is 14x5.5J at ET35 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Daihatsu Cuore?
For a flush look with minimal to no rubbing, we recommend 13x5.0J at ET35 offset as a starting point on a stock or mildly lowered Daihatsu Cuore.
Do I need wheel spacers for my Daihatsu Cuore?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Daihatsu Cuore?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 4.38" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Daihatsu Cuore?
The Daihatsu Cuore runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.