Metallic Gray Split Directional Milled Forged Wheels
Monoblock · Metallic Gray
2010 TechArt Porsche Panamera Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting TechArt Porsche Panamera wheels? This page gives the 2010 TechArt Porsche Panamera bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged TechArt Porsche Panamera rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2010 TechArt Porsche Panamera uses a 5x130 bolt pattern with a 71.6 mm centre bore and M14x1.5 lug bolts. For aftermarket wheels, 21x10J ET45 front / 21x11.5J ET42 rear sits flush.
Forged wheels for the 2010 TechArt Porsche Panamera — drilled 5x130 with a 71.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
TechArt Porsche Panamera (2010): 5x130 bolt pattern, 71.6mm center bore, OE F 20x9.5J ET60 / R 20x11J ET52. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2010
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 21x10J ET45 / R 21x11.5J ET42 |
Forged Wheel Designs for the TechArt Porsche Panamera
Every design below is forged to order, so it can be machined to the TechArt Porsche Panamera's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
Black / Machined Directional Milled Machined Face Forged Wheels
Monoblock · Black Machined
Black / White Aero 5 Y-Spoke Forged Wheels
Monoblock · Black / White
Bright Silver 5 V-Spoke Forged Wheels
Monoblock · Bright Silver
HRE P101-Style Gold 5 Y-Spoke Forged Wheels
Replica · Gold
Silver / Gunmetal 5-Spoke Forged Wheels
Monoblock · Silver / Gunmetal
BBS Silver 10 Y-Spoke Deep Lip Forged Wheels
Deep Dish · Silver
Matte Navy Blue 6-Spoke Forged Wheels
Monoblock · Matte Navy Blue
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The TechArt Porsche Panamera ships from the factory on a 5x130 bolt pattern with a 71.6mm center bore and a F 20x9.5J ET60 / R 20x11J ET52 wheel. Our flush reference for the TechArt Porsche Panamera is F 21x10J ET45 / R 21x11.5J ET42.; our maximum aggressive reference is F 22x10.5J ET40 / R 22x12J ET38. — beyond that, expect clearance issues against the fender liner without further modification.
TechArt Porsche Panamera OE Wheel Specs
The TechArt Porsche Panamera ships from the factory on 5x130 bolt pattern wheels with a 71.6mm center bore. The stock wheel size is F 20x9.5J ET60 / R 20x11J ET52, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the TechArt Porsche Panamera (2010) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 20x9.5J | ET60 | 7.61 in (193 mm) | — | — |
| Flush | 21x10J | ET45 | 7.27 in (185 mm) | −9 mm | +21 mm |
| Maximum | 22x10.5J | ET40 | 7.32 in (186 mm) | −7 mm | +33 mm |
Vehicles With the Same Hub as the TechArt Porsche Panamera (5x130, 71.6 mm Bore)
In our database, 294 other vehicle entries from 10 makes use exactly the same 5x130 bolt pattern and 71.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle pages in our English fitment guide (375 of 6,503); 78.7% of those also use a 71.6 mm center bore.
Hub-Centric Rings for a 71.6 mm Center Bore
A wheel with a center bore larger than 71.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 72.6 mm | 72.6 → 71.6 mm |
| 73.1 mm | 73.1 → 71.6 mm |
| 74.1 mm | 74.1 → 71.6 mm |
| 76.1 mm | 76.1 → 71.6 mm |
ANKUSI forged wheels are bored to exactly 71.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the TechArt Porsche Panamera use?
The 2010 TechArt Porsche Panamera uses a 5x130 bolt pattern.
How many lug bolts does the TechArt Porsche Panamera use?
The TechArt Porsche Panamera uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the TechArt Porsche Panamera?
The TechArt Porsche Panamera's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the TechArt Porsche Panamera?
For a flush look with minimal to no rubbing, we recommend F 21x10J ET45 / R 21x11.5J ET42 as a starting point on a stock or mildly lowered TechArt Porsche Panamera.
Do I need wheel spacers for my TechArt Porsche Panamera?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my TechArt Porsche Panamera?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 7.27" backspacing up front and 7.9" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my TechArt Porsche Panamera?
Yes — the TechArt Porsche Panamera's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 20x9.5 wheels · 20 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.