BBS Silver Riveted Forged Wheels
Deep Dish · Silver
2007 Porsche 911 Carrera 4S Cabriolet Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche 911 Carrera 4S Cabriolet wheels? This page gives the 2007 Porsche 911 Carrera 4S Cabriolet bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche 911 Carrera 4S Cabriolet rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche 911 Carrera 4S Cabriolet (2007): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 19x8J R: 19x11J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Caliper TypeFixed 4-piston caliper, all four corners (OEM, Porsche)
Year2007
CategorySports Convertible
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 19x8J R: 19x11J |
| Flush Fitment | F 19x9J ET50 / R 19x11J ET52 |
| Maximum Aggressive | F 19x8.5J ET37 / R 19x11J ET31 |
Forged Wheel Designs for the Porsche 911 Carrera 4S Cabriolet
Every design below is forged to order, so it can be machined to the Porsche 911 Carrera 4S Cabriolet's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
Silver 5-Spoke Forged Wheels
Monoblock · Silver
BBS RS-Style Gold / Silver Deep Lip Forged Wheels
Deep Dish · Gold / Silver
Gloss Black / Gunmetal / Gray 5 Y-Spoke Forged Wheels
Monoblock · Gloss Black / Gunmetal / Gray
Porsche OEM-Style Matte Bronze 5 Y-Spoke Concave Forged Wheels
Replica · Matte Bronze
APEX-Style Hyper Silver 5 Y-Spoke Forged Wheels
Monoblock · Hyper Silver
Wheelforce-Style Satin Blue Side-Milled Split 5-Spoke Forged Wheels
Monoblock · Satin Blue
Matte Silver Center-Lock Forged Wheels
Center-Lock · Matte Silver
See all Porsche 911 wheel designs Porsche OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A convertible carries its extra structural weight low and behind the axle line, so wheel mass and offset changes show up in ride and steering feel faster than they do on the coupe. A forged wheel keeps the rotating mass down while you add the width the arches will take.
The Porsche 911 Carrera 4S Cabriolet runs a 5x130 fitment, 71.6mm center bore, and a F: 19x8J wheel from the factory. Our Flush Fitment reference is F 19x9J ET50 / R 19x11J ET52, which tucks the tire under the fender lip on a stock-height Porsche 911 Carrera 4S Cabriolet. Our Maximum Aggressive reference is F 19x8.5J ET37 / R 19x11J ET31 - beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Porsche 911 Carrera 4S Cabriolet OE Wheel Specs
The 2007 Porsche 911 Carrera 4S Cabriolet (Sports Convertible) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 19x8J R: 19x11J.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche 911 Carrera 4S Cabriolet (2007) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
SSR GT3 19x8.5 ET37 / 19x11 ET31, 255/35-19 & 325/30-19, coilovers, rolled and trimmed rear fenders (997 C4S); 20in option Rohana RFX02 20x9 ET45 / 20x12 ET42, PS4S 245/35-20 & 305/30-20, factory suspension + slight roll 997.1 AWD widebody. Match front/rear rolling diameters for the AWD driveline. Verified on the 997.1 C4S widebody platform. Cabriolet uses the same track width, so wheel fitment is identical to the coupe.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 19x8J ET57 → ~6.74″ F backspacing, R 19x11J ET51 → ~8.01″ R backspacing
- Flush: F 19x9J ET50 → ~6.97″ F backspacing, R 19x11J ET52 → ~8.05″ R backspacing
- Max: F 19x8.5J ET37 → ~6.21″ F backspacing, R 19x11J ET31 → ~7.22″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche 911 Carrera 4S Cabriolet? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Porsche 911 Carrera 4S Cabriolet use?
The 2007 Porsche 911 Carrera 4S Cabriolet uses a 5x130 bolt pattern.
How many lug bolts does the Porsche 911 Carrera 4S Cabriolet use?
The Porsche 911 Carrera 4S Cabriolet uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche 911 Carrera 4S Cabriolet?
The Porsche 911 Carrera 4S Cabriolet's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche 911 Carrera 4S Cabriolet?
Factory wheels on the Porsche 911 Carrera 4S Cabriolet are F: 19x8J R: 19x11J.
What is the biggest wheel size I can fit on my Porsche 911 Carrera 4S Cabriolet without rubbing?
The most aggressive fitment we recommend without fender work is F 19x8.5J ET37 / R 19x11J ET31. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche 911 Carrera 4S Cabriolet?
For a flush look with minimal to no rubbing, we recommend F 19x9J ET50 / R 19x11J ET52 as a starting point on a stock or mildly lowered Porsche 911 Carrera 4S Cabriolet.
Do I need wheel spacers for my Porsche 911 Carrera 4S Cabriolet?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche 911 Carrera 4S Cabriolet?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.97" backspacing up front and 8.05" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche 911 Carrera 4S Cabriolet?
Yes — the Porsche 911 Carrera 4S Cabriolet's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.