BBS LM-Style Gunmetal Mesh Polished Lip 2-Piece Forged Wheels
Porsche 911 / GT-R Fitment · 5-Lug
2004 Porsche Cayenne S Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche Cayenne S wheels? This page gives the 2004 Porsche Cayenne S bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche Cayenne S rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2004 Porsche Cayenne S uses a 5x130 bolt pattern with a 71.6 mm centre bore and M14x1.5 lug bolts. Factory wheels: 18x8J at ET57. For aftermarket wheels, 20x9J ET50 sits flush and 22x10J ET50 is the most aggressive fit.
Forged wheels for the 2004 Porsche Cayenne S — drilled 5x130 with a 71.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in about 25 days.
Get a quote for this car
Porsche Cayenne S (2004): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: 18x8J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2004
CategorySUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Built to order by ANKUSI — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8J at ET57 |
| Flush Fitment | 20x9J at ET50 offset |
| Maximum Aggressive | 22x10J at ET50 offset |
Forged wheels for the Porsche Cayenne SMachined to the 5x130 bolt pattern and 71.6 mm bore · 14–24 inch · offset calculated for your car · 3D drawing before production
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Because an SUV's center of gravity is already higher than a sedan's, anything added at the corners — including wheel weight — has an outsized effect on handling balance. A forged wheel lets us hit the visual stance owners want without adding the rotational mass a cast wheel of the same strength would carry.
The Porsche Cayenne S runs a 5x130 bolt pattern, 71.6mm center bore, and a 18x8J at ET57, front and rear, wheel from the factory. Our Flush Fitment reference is 20x9J ET50, which tucks the tire under the fender lip on a stock-height Porsche Cayenne S. Our Maximum Aggressive reference is 22x10J ET50 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Porsche Cayenne S OE Wheel Specs
The 2004 Porsche Cayenne S (SUV) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are 18x8J at ET57.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche Cayenne S (2004) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look with minimal rubbing, 20x9J ET50 is the recommended starting point on a stock or mildly lowered Porsche Cayenne S.
Maximum Aggressive Fitment
22x10J ET50 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
Real-World Fitment Notes
20-22in forged, VR Forged D07 18x9 ET20 for off-road/overland; hub-centric flange on rotor hats 955 Cayenne S; verified wheel-size.com/Rennlist 5x130 Cayenne data 18x8J ET57 square, 5x130, CB71.6
5-Tier Configuration Options
A Factory-Style 18x8.0J ET57
Recommended setup: 18x8.0J ET57 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,200-1,500 (wheels + tires + install)
B Comfortable Upgrade 19x8.5J ET54
Recommended setup: 19x8.5J ET54 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 20x9.0J ET50
Recommended setup: 20x9.0J ET50 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 21x9.5J ET50
Recommended setup: 21x9.5J ET50 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 22x10.0J ET50
Recommended setup: 22x10.0J ET50 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 18x8.0J ET57 | 19x8.5J ET54 | 20x9.0J ET50 | 21x9.5J ET50 | 22x10.0J ET50 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $1,200-1,500 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 18x8.0J ET57
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 20x9.0J ET50
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 22x10.0J ET50
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
1
What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.
2
What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.
3
How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.
4
Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Porsche Cayenne S owners.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x8J ET57 → ~6.74″ backspacing
- Flush: 20x9J ET50 → ~6.97″ backspacing
- Max: 22x10J ET50 → ~7.47″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche Cayenne S? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the Porsche Cayenne S (2004)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x130 pattern and the 71.6mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most Porsche orders on this platform land somewhere between the 20x9J ET50 flush setup and the 22x10J ET50 aggressive setup referenced above.
Designs we already tool for the 5x130 pattern — each one is re-cut to your sizes and offsets:
Porsche 911 / BMW M3 Forged Wheels – Gloss White 5-Spoke
HRE 522M-Style Polished Silver 5-Spoke Directional Forged Wheels - Porsche Cayenne / Porsche 911 Fitment (5-Lug)
Porsche 911 / BMW M3 Forged Wheels – Mirror Polished 5-Spoke Deep-Lip (5-Lug)
HRE-Style Bronze 5 Y-Spoke Forged Wheels – Porsche 911 / M3 Fitment (5-Lug)Frequently Asked Questions
What bolt pattern (PCD) does the Porsche Cayenne S use?
The 2004 Porsche Cayenne S uses a 5x130 bolt pattern.
How many lug bolts does the Porsche Cayenne S use?
The Porsche Cayenne S uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche Cayenne S?
The Porsche Cayenne S's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche Cayenne S?
Factory wheels on the Porsche Cayenne S are 18x8J at ET57.
What is the biggest wheel size I can fit on my Porsche Cayenne S without rubbing?
The most aggressive fitment we recommend without fender work is 22x10J at ET50 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche Cayenne S?
For a flush look with minimal to no rubbing, we recommend 20x9J at ET50 offset as a starting point on a stock or mildly lowered Porsche Cayenne S.
Do I need wheel spacers for my Porsche Cayenne S?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche Cayenne S?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.97" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche Cayenne S?
The Porsche Cayenne S runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Vehicles With the Same Hub as the Porsche Cayenne S (5x130, 71.6 mm Bore)
In our database, 293 other vehicle entries from 10 makes use exactly the same 5x130 bolt pattern and 71.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle pages in our English fitment guide (375 of 6,503); 78.7% of those also use a 71.6 mm center bore.
Porsche Cayenne S: Specs by Model Year
| Year | Bolt pattern | Center bore | Factory wheel |
|---|---|---|---|
| 2004 | 5x130 | 71.6 mm | 18x8J |
| 2024 | 5x130 | 71.6 mm | 20x9J |
Bolt pattern and center bore stay the same across all 2 model years in our database (2004–2024).
Hub-Centric Rings for a 71.6 mm Center Bore
A wheel with a center bore larger than 71.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 72.6 mm | 72.6 → 71.6 mm |
| 73.1 mm | 73.1 → 71.6 mm |
| 74.1 mm | 74.1 → 71.6 mm |
| 76.1 mm | 76.1 → 71.6 mm |
ANKUSI forged wheels are bored to exactly 71.6 mm for this vehicle, so no ring is needed.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Forged Wheel Designs for the Porsche Cayenne S
Every design below is forged to order, so it can be machined to the Porsche Cayenne S's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
HRE-Style Gloss Black 5 Y-Spoke Forged Wheels
Porsche 911 / BMW M3 G80 Fitment · 5-Lug
Edition 26-Style Metallic Gunmetal 20-Spoke Forged Wheels
Porsche 911 992 / 911 991 Fitment · 5-Lug
Porsche 911 / Panamera Forged Wheels
Gloss Black / Gunmetal / Gray 5 Y-Spoke
HRE P104SC-Style Mirror Polished Silver 5 V-Spoke Forged Wheels - Porsche 911 / Porsche 718 Cayman Fitment (5-Lug)
HRE-Style forged wheels featuring the mirror polished silver 5 V-spoke design, forged to order at ANKUSI's Guangzhou plant. Bolt pattern, centre bore, diameter, width and offset are machined for your exact vehicle — this listing covers 5-lug applications.
BBS-Style Brushed Silver 10-Spoke Deep-Lip Forged Wheels
BMW M3 G80 / Porsche 911 Fitment · 5-Lug
Wheelforce-Style Gunmetal 10-Spoke Forged Wheels
Porsche 911 / M3 Fitment · 5-Lug
Porsche 911 / BMW M3 Forged Wheels
Gunmetal Multi-Spoke
Bolt pattern and center bore on this page were cross-checked against at least two independent sources before publication. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.