Rays-Style Blue 6-Spoke Forged Wheels
Monoblock · Blue
2007 Rinspeed Porsche 997 Turbo Le Mans 600 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Rinspeed Porsche 997 Turbo Le Mans 600 wheels? This page gives the 2007 Rinspeed Porsche 997 Turbo Le Mans 600 bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Rinspeed Porsche 997 Turbo Le Mans 600 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2007 Rinspeed Porsche 997 Turbo Le Mans 600 uses a 5x130 bolt pattern with a 71.6 mm centre bore. For aftermarket wheels, 20x9J ET45 front / 20x12J ET45 rear sits flush.
Forged wheels for the 2007 Rinspeed Porsche 997 Turbo Le Mans 600 — drilled 5x130 with a 71.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Rinspeed Porsche 997 Turbo Le Mans 600 (2007): 5x130 bolt pattern, 71.6mm center bore, OE F 20x8.5J ET46 / R 20x11J ET46.
Bolt Pattern5x130
Center Bore71.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2007
Category5-Lug Supercar (2-Piece)
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 20x9J ET45 / R 20x12J ET45 |
Forged Wheel Designs for the Rinspeed Porsche 997 Turbo Le Mans 600
Every design below is forged to order, so it can be machined to the Rinspeed Porsche 997 Turbo Le Mans 600's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
HRE-Style Chrome 5 Y-Spoke Forged Wheels
Monoblock · Chrome
Bronze 5 Y-Spoke Forged Wheels
Replica · Bronze
HRE 522M-Style Gold 5-Spoke Forged Wheels
Replica · Gold
Wheelforce-Style Brushed Silver 5 W-Spoke Forged Wheels
Monoblock · Brushed Silver
Transparent Gray Petal-Spoke Forged Wheels
Monoblock · Transparent Gray
HRE P101-Style Brushed Silver / Silver 10-Spoke Forged Wheels
Replica · Brushed Silver / Silver
Brabus-Style Gunmetal / Machined Multi-Spoke Forged Wheels
Monoblock · Gunmetal / Machined
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a supercar, wheel weight is one of the few remaining places to cut rotational mass without touching the powertrain or chassis the factory already optimized. Forging gets there at the same structural margin as the OE wheel, which is exactly the trade a car built around outright performance rewards.
The Rinspeed Porsche 997 Turbo Le Mans 600 ships from the factory on a 5x130 bolt pattern with a 71.6mm center bore and a F 20x8.5J ET46 / R 20x11J ET46 wheel. Our flush reference for the Rinspeed Porsche 997 Turbo Le Mans 600 is F 20x9J ET45 / R 20x12J ET45.; our maximum aggressive reference is F 20x9.5J ET40 / R 20x12.5J ET40. — beyond that, expect clearance issues against the fender liner without further modification.
Rinspeed Porsche 997 Turbo Le Mans 600 OE Wheel Specs
The Rinspeed Porsche 997 Turbo Le Mans 600 ships from the factory on 5x130 bolt pattern wheels with a 71.6mm center bore. The stock wheel size is F 20x8.5J ET46 / R 20x11J ET46, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Rinspeed Porsche 997 Turbo Le Mans 600 (2007) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
- OE 20x8.5J ET46: backspacing ≈ 6.56"
- Flush 20x9J ET45: backspacing ≈ 6.77"
- Max 20x9.5J ET40: backspacing ≈ 6.82"
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Rinspeed Porsche 997 Turbo Le Mans 600.
Vehicles With the Same Hub as the Rinspeed Porsche 997 Turbo Le Mans 600 (5x130, 71.6 mm Bore)
In our database, 294 other vehicle entries from 10 makes use exactly the same 5x130 bolt pattern and 71.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle pages in our English fitment guide (375 of 6,503); 78.7% of those also use a 71.6 mm center bore.
Hub-Centric Rings for a 71.6 mm Center Bore
A wheel with a center bore larger than 71.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 72.6 mm | 72.6 → 71.6 mm |
| 73.1 mm | 73.1 → 71.6 mm |
| 74.1 mm | 74.1 → 71.6 mm |
| 76.1 mm | 76.1 → 71.6 mm |
ANKUSI forged wheels are bored to exactly 71.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Rinspeed Porsche 997 Turbo Le Mans 600 use?
The 2007 Rinspeed Porsche 997 Turbo Le Mans 600 uses a 5x130 bolt pattern.
How many lug bolts does the Rinspeed Porsche 997 Turbo Le Mans 600 use?
The Rinspeed Porsche 997 Turbo Le Mans 600 uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Rinspeed Porsche 997 Turbo Le Mans 600?
The Rinspeed Porsche 997 Turbo Le Mans 600's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Rinspeed Porsche 997 Turbo Le Mans 600?
For a flush look with minimal to no rubbing, we recommend F 20x9J ET45 / R 20x12J ET45 as a starting point on a stock or mildly lowered Rinspeed Porsche 997 Turbo Le Mans 600.
Do I need wheel spacers for my Rinspeed Porsche 997 Turbo Le Mans 600?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Rinspeed Porsche 997 Turbo Le Mans 600?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.77" backspacing up front and 8.27" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Rinspeed Porsche 997 Turbo Le Mans 600?
Yes — the Rinspeed Porsche 997 Turbo Le Mans 600's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.