
2016 Nissan NP300 Navara Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Nissan NP300 Navara wheels? This page gives the 2016 Nissan NP300 Navara bolt pattern (6x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Nissan NP300 Navara rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Nissan NP300 Navara (2016): 6x114.3 bolt pattern, 66.1mm center bore. Factory wheels: 18x7.0J at ET45 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7.0J F/R |
| Flush Fitment | 17x8.0J at ET20 offset |
| Maximum Aggressive | 18x9.0J at ET10 offset |
Forged Wheel Designs for the Nissan NP300 Navara
Every design below is forged to order, so it can be machined to the Nissan NP300 Navara's 6x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.


DT Forge Pink & Chrome Multi-Spoke Wheels
H-Type · Pink / Chrome

American Force Polished Multi-Spoke Wheels
H-Type · Polished

MMX Design Polished 5-Spoke Forged Wheels
H-Type · Polished

KG1 Forged Radar Polished Forged Wheels
H-Type · Polished
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
Trucks live and die on unsprung weight and load capacity — every pound added at the wheel is a pound the suspension has to control over every bump, fully loaded or not. Forging the wheel instead of casting it lets us hold the factory load rating while cutting rotational mass, which pays off directly in ride quality and steering response on a vehicle that spends real time towing or hauling.
The Nissan NP300 Navara runs a 6x114.3 bolt pattern, 66.1mm center bore, and a 18x7.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x8.0J ET20, which tucks the tire under the fender lip on a stock-height Nissan NP300 Navara. Our Maximum Aggressive reference is 18x9.0J ET10 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Nissan NP300 Navara OE Wheel Specs
The 2016 Nissan NP300 Navara (Midsize Pickup) uses a 6x114.3 bolt pattern with a 66.1mm center bore. Factory wheels are 18x7.0J F/R.
Why the factory spec works for most owners:
- Supports higher payload and towing capacity
- Preserves ground clearance for towing, hauling and light off-road use
- Matches tire sizing commonly available for this class of vehicle
- Maintains clearance for the factory suspension and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan NP300 Navara (2016) we drill the 6x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x7.0J ET45 → ~5.77″ backspacing
- Flush: 17x8.0J ET20 → ~5.29″ backspacing
- Max: 18x9.0J ET10 → ~5.39″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Nissan spec, or want a wheel built to a custom offset for your Nissan NP300 Navara? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Nissan NP300 Navara use?
How many lug bolts does the Nissan NP300 Navara use?
What is the center bore size on the Nissan NP300 Navara?
What size are the factory (stock) wheels on the Nissan NP300 Navara?
What is the biggest wheel size I can fit on my Nissan NP300 Navara without rubbing?
What does a flush wheel fitment look like on the Nissan NP300 Navara?
Do I need wheel spacers for my Nissan NP300 Navara?
How do I calculate wheel backspacing for my Nissan NP300 Navara?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Nissan NP300 Navara?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.25, conical-seat lug nut.
Factory Torque Spec: 103-122 Nm (76-90 ft-lb). Range covers most Nissan passenger cars and crossovers on M12x1.25 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.