2020 Kia Cadenza Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Kia Cadenza wheels? This page gives the 2020 Kia Cadenza bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Kia Cadenza rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2020 Kia Cadenza uses a 5x114.3 bolt pattern with a 67.1 mm centre bore and M14x1.5 lug nuts. Factory wheels: 19x8.0J, front and rear. For aftermarket wheels, 20x8.5J ET38 sits flush and 20x9.0J ET32 is the most aggressive fit.
Forged wheels for the 2020 Kia Cadenza — drilled 5x114.3 with a 67.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Kia Cadenza (2020): 5x114.3 bolt pattern, 67.1mm center bore. Factory wheels: 19x8.0J F/R. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM14x1.5 Nut
Center Bore67.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2020
CategorySedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x8.0J F/R |
| Flush Fitment | 20x8.5J at ET38 offset |
| Maximum Aggressive | 20x9.0J at ET32 offset |
Forged Wheel Designs for the Kia Cadenza
Every design below is forged to order, so it can be machined to the Kia Cadenza's 5x114.3 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
Gloss Black Y-Spoke Mesh Forged Wheels
Monoblock · Gloss Black
Alpine OEM-Style Hyper Silver 5 Y-Spoke Forged Wheels
Monoblock · Hyper Silver
Gloss Black Polished Split 5-Spoke Forged Wheels
Monoblock · Gloss Black
Vossen-Style Bright Silver Y-Spoke Mesh Forged Wheels
Monoblock · Bright Silver
EvoCorse-Style Satin Black 12-Spoke Rally Forged Wheels
Monoblock · Satin Black
HRE-Style Polished 5 Split Y-Spoke Forged Wheels
Monoblock · Polished
Kia OEM-Style Gloss Black Multi-Spoke Turbine Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Kia Cadenza runs a 5x114.3 bolt pattern, 67.1mm center bore, and a 19x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x8.5J ET38, which tucks the tire under the fender lip on a stock-height Kia Cadenza. Our Maximum Aggressive reference is 20x9.0J ET32 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Kia Cadenza OE Wheel Specs
The 2020 Kia Cadenza (Sedan) uses a 5x114.3 bolt pattern with a 67.1mm center bore. Factory wheels are 19x8.0J F/R.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Kia Cadenza (2020) we drill the 5x114.3 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x8.0J ET40 → ~6.07″ backspacing
- Flush: 20x8.5J ET38 → ~6.25″ backspacing
- Max: 20x9.0J ET32 → ~6.26″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Kia spec, or want a wheel built to a custom offset for your Kia Cadenza? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Kia Cadenza: Specs by Model Year
| Year | Bolt pattern | Center bore | Factory wheel |
|---|---|---|---|
| 2014 | 5x114.3 | 67.1 mm | 19x8J |
| 2017 | 5x114.3 | 67.1 mm | 19x8J |
| 2020 | 5x114.3 | 67.1 mm | 19x8J |
Bolt pattern and center bore stay the same across all 3 model years in our database (2014–2020).
Vehicles With the Same Hub as the Kia Cadenza (5x114.3, 67.1 mm Bore)
In our database, 456 other vehicle entries from 30 makes use exactly the same 5x114.3 bolt pattern and 67.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 35.2% of those also use a 67.1 mm center bore.
Hub-Centric Rings for a 67.1 mm Center Bore
A wheel with a center bore larger than 67.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 67.1 mm |
| 70.5 mm | 70.5 → 67.1 mm |
| 71.6 mm | 71.6 → 67.1 mm |
| 72.6 mm | 72.6 → 67.1 mm |
| 73.1 mm | 73.1 → 67.1 mm |
ANKUSI forged wheels are bored to exactly 67.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Kia Cadenza use?
The 2020 Kia Cadenza uses a 5x114.3 bolt pattern.
How many lug bolts does the Kia Cadenza use?
The Kia Cadenza uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Kia Cadenza?
The Kia Cadenza's center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Kia Cadenza?
Factory wheels on the Kia Cadenza are 19x8.0J F/R.
What is the biggest wheel size I can fit on my Kia Cadenza without rubbing?
The most aggressive fitment we recommend without fender work is 20x9.0J at ET32 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Kia Cadenza?
For a flush look with minimal to no rubbing, we recommend 20x8.5J at ET38 offset as a starting point on a stock or mildly lowered Kia Cadenza.
Do I need wheel spacers for my Kia Cadenza?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Kia Cadenza?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.25" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Kia Cadenza?
The Kia Cadenza runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 107-127 Nm (79-94 ft-lb). Range covers most Kia passenger cars and crossovers on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x8 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.