OZ Racing-Style Polished Turbofan Dish Riveted Lip Forged Wheels
2-Piece · Polished
2025 Kia Carnival Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Kia Carnival wheels? This page gives the 2025 Kia Carnival bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Kia Carnival rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 Kia Carnival uses a 5x114.3 bolt pattern with a 67.1 mm centre bore and M14x1.5 lug nuts. Factory wheels: 19x7.5J, front and rear. For aftermarket wheels, 20x8.5J ET35 sits flush and 21x9.0J ET35 is the most aggressive fit.
Forged wheels for the 2025 Kia Carnival — drilled 5x114.3 with a 67.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Kia Carnival (2025): 5x114.3 bolt pattern, 67.1mm center bore. Factory wheels: 19x7.5J F/R. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM14x1.5 Nut
Center Bore67.1mm
Wheel Load Rating900–1100 kg/wheel (Van / MPV segment reference)
Year2025
CategoryMinivan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x7.5J F/R |
| Flush Fitment | 20x8.5J at ET35 offset |
| Maximum Aggressive | 21x9.0J at ET35 offset |
Forged Wheel Designs for the Kia Carnival
Every design below is forged to order, so it can be machined to the Kia Carnival's 5x114.3 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
Satin Gunmetal 5-Spoke Forged Wheels
Monoblock · Satin Gunmetal
Vossen LC3-01T-Style Brushed Silver 5-Spoke Forged Wheels
Replica · Brushed Silver
Honda Civic Type R Forged Wheels
Monoblock
Kia OEM-Style Gloss Black Multi-Spoke Turbine Forged Wheels
Monoblock · Gloss Black
HRE-Style Polished 5 Split Y-Spoke Forged Wheels
Monoblock · Polished
EvoCorse-Style Satin Black 12-Spoke Rally Forged Wheels
Monoblock · Satin Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Minivans carry passengers and cargo across a wide range of loaded conditions, so the factory wheel spec is built around a conservative load margin. Forging lets us hold that same margin while trimming rotational mass, which shows up as smoother ride quality whether the vehicle is empty or fully loaded.
The Kia Carnival runs a 5x114.3 bolt pattern, 67.1mm center bore, and a 19x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x8.5J ET35, which tucks the tire under the fender lip on a stock-height Kia Carnival. Our Maximum Aggressive reference is 21x9.0J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Kia Carnival OE Wheel Specs
The 2025 Kia Carnival (Minivan) uses a 5x114.3 bolt pattern with a 67.1mm center bore. Factory wheels are 19x7.5J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Kia Carnival (2025) we drill the 5x114.3 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x7.5J ET50 → ~6.22″ backspacing
- Flush: 20x8.5J ET35 → ~6.13″ backspacing
- Max: 21x9.0J ET35 → ~6.38″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Kia spec, or want a wheel built to a custom offset for your Kia Carnival? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Kia Carnival: Specs by Model Year
| Year | Bolt pattern | Center bore | Factory wheel |
|---|---|---|---|
| 2022 | 5x114.3 | 67.1 mm | 19x7.5J |
| 2025 | 5x114.3 | 67.1 mm | 19x7.5J |
Bolt pattern and center bore stay the same across all 2 model years in our database (2022–2025).
Vehicles With the Same Hub as the Kia Carnival (5x114.3, 67.1 mm Bore)
In our database, 456 other vehicle entries from 30 makes use exactly the same 5x114.3 bolt pattern and 67.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 35.2% of those also use a 67.1 mm center bore.
Hub-Centric Rings for a 67.1 mm Center Bore
A wheel with a center bore larger than 67.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 67.1 mm |
| 70.5 mm | 70.5 → 67.1 mm |
| 71.6 mm | 71.6 → 67.1 mm |
| 72.6 mm | 72.6 → 67.1 mm |
| 73.1 mm | 73.1 → 67.1 mm |
ANKUSI forged wheels are bored to exactly 67.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Kia Carnival use?
The 2025 Kia Carnival uses a 5x114.3 bolt pattern.
How many lug bolts does the Kia Carnival use?
The Kia Carnival uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Kia Carnival?
The Kia Carnival's center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Kia Carnival?
Factory wheels on the Kia Carnival are 19x7.5J F/R.
What is the biggest wheel size I can fit on my Kia Carnival without rubbing?
The most aggressive fitment we recommend without fender work is 21x9.0J at ET35 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Kia Carnival?
For a flush look with minimal to no rubbing, we recommend 20x8.5J at ET35 offset as a starting point on a stock or mildly lowered Kia Carnival.
Do I need wheel spacers for my Kia Carnival?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Kia Carnival?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.13" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Kia Carnival?
The Kia Carnival runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 107-127 Nm (79-94 ft-lb). Range covers most Kia passenger cars and crossovers on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x7.5 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.