Fiat OEM-Style Fiat Bright Silver Full-Face Forged Wheels
Monoblock · Bright Silver
2021 Fiat 500X Yachting Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Fiat 500X Yachting wheels? This page gives the 2021 Fiat 500X Yachting bolt pattern (5x110), centre bore, factory rim size and the offset range for aftermarket and forged Fiat 500X Yachting rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2021 Fiat 500X Yachting uses a 5x110 bolt pattern with a 65.1 mm centre bore and M12x1.25 lug bolts. Factory wheels: 18x7.0J, front and rear. For aftermarket wheels, 19x8.0J ET35 sits flush and 20x8.5J ET30 is the most aggressive fit.
Forged wheels for the 2021 Fiat 500X Yachting — drilled 5x110 with a 65.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Fiat 500X Yachting (2021): 5x110 bolt pattern, 65.1mm center bore. Factory wheels: 18x7.0J F/R. Reference fitment ranges.
Bolt Pattern5x110
Wheel Bolt/NutM12x1.25 Bolt
Center Bore65.1mm
Wheel Load Rating800–950 kg/wheel (Crossover segment reference)
Year2021
CategoryCrossover
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7.0J F/R |
| Flush Fitment | 19x8.0J at ET35 offset |
| Maximum Aggressive | 20x8.5J at ET30 offset |
Forged Wheel Designs for the Fiat 500X Yachting
Every design below is forged to order, so it can be machined to the Fiat 500X Yachting's 5x110 bolt pattern and 65.1 mm center bore, with the width and offset calculated for your setup.
Maybach-Style Chrome Wire Forged Wheels
Monoblock · Chrome
Black / Machined 5-Spoke Machined Face Forged Wheels
Monoblock · Black Machined
Corvette OEM-Style Polished Silver 5 Y-Spoke Beadlock Off-Road Forged Wheels
Off-Road Beadlock · Polished Silver
Transparent Copper Petal Forged Wheels
Monoblock · Transparent Copper
Corvette OEM-Style Gloss Black Red-Ring Beadlock Off-Road Forged Wheels
Off-Road Beadlock · Gloss Black / Red
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Fiat 500X Yachting's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Fiat 500X Yachting runs a 5x110 bolt pattern, 65.1mm center bore, and a 18x7.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.0J ET35, which tucks the tire under the fender lip on a stock-height Fiat 500X Yachting. Our Maximum Aggressive reference is 20x8.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Fiat 500X Yachting OE Wheel Specs
The 2021 Fiat 500X Yachting (Crossover) uses a 5x110 bolt pattern with a 65.1mm center bore. Factory wheels are 18x7.0J F/R.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Fiat 500X Yachting (2021) we drill the 5x110 pattern and cut the centre bore to 65.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x7.0J ET40 → ~5.57″ backspacing
- Flush: 19x8.0J ET35 → ~5.88″ backspacing
- Max: 20x8.5J ET30 → ~5.93″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Fiat spec, or want a wheel built to a custom offset for your Fiat 500X Yachting? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Fiat 500X Yachting (5x110, 65.1 mm Bore)
In our database, 139 other vehicle entries from 19 makes use exactly the same 5x110 bolt pattern and 65.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x110 is used by 2.2% of the vehicle pages in our English fitment guide (145 of 6,503); 96.6% of those also use a 65.1 mm center bore.
Hub-Centric Rings for a 65.1 mm Center Bore
A wheel with a center bore larger than 65.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.1 mm | 66.1 → 65.1 mm |
| 66.6 mm | 66.6 → 65.1 mm |
| 67.1 mm | 67.1 → 65.1 mm |
| 70.1 mm | 70.1 → 65.1 mm |
| 73.1 mm | 73.1 → 65.1 mm |
ANKUSI forged wheels are bored to exactly 65.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Fiat 500X Yachting use?
The 2021 Fiat 500X Yachting uses a 5x110 bolt pattern.
How many lug bolts does the Fiat 500X Yachting use?
The Fiat 500X Yachting uses a 5-lug bolt pattern (5x110), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Fiat 500X Yachting?
The Fiat 500X Yachting's center bore is 65.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Fiat 500X Yachting?
Factory wheels on the Fiat 500X Yachting are 18x7.0J F/R.
What is the biggest wheel size I can fit on my Fiat 500X Yachting without rubbing?
The most aggressive fitment we recommend without fender work is 20x8.5J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Fiat 500X Yachting?
For a flush look with minimal to no rubbing, we recommend 19x8.0J at ET35 offset as a starting point on a stock or mildly lowered Fiat 500X Yachting.
Do I need wheel spacers for my Fiat 500X Yachting?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Fiat 500X Yachting?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Fiat 500X Yachting?
The Fiat 500X Yachting runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x7 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.