
2010 Nissan Pathfinder Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Nissan Pathfinder wheels? This page gives the 2010 Nissan Pathfinder bolt pattern (6x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Nissan Pathfinder rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Nissan Pathfinder (2010): 6x114.3 bolt pattern, 66.1mm center bore. Factory wheels: 18x8.0J at ET30 offset, front and rear. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8.0J F/R |
| Flush Fitment | 18x9.0J at ET15 offset |
| Maximum Aggressive | 20x9.0J at ET0 offset |
Forged Wheel Designs for the Nissan Pathfinder
Every design below is forged to order, so it can be machined to the Nissan Pathfinder's 6x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.


KG1 Forged Radar Polished Forged Wheels
H-Type · Polished

MMX Design Polished 5-Spoke Forged Wheels
H-Type · Polished

American Force Polished Multi-Spoke Wheels
H-Type · Polished

DT Forge Pink & Chrome Multi-Spoke Wheels
H-Type · Pink / Chrome
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
The Nissan Pathfinder's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Nissan Pathfinder runs a 6x114.3 bolt pattern, 66.1mm center bore, and a 18x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x9.0J ET15, which tucks the tire under the fender lip on a stock-height Nissan Pathfinder. Our Maximum Aggressive reference is 20x9.0J ET0 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Nissan Pathfinder OE Wheel Specs
The 2010 Nissan Pathfinder (Full-Size SUV) uses a 6x114.3 bolt pattern with a 66.1mm center bore. Factory wheels are 18x8.0J F/R.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan Pathfinder (2010) we drill the 6x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x8.0J ET30 → ~5.68″ backspacing
- Flush: 18x9.0J ET15 → ~5.59″ backspacing
- Max: 20x9.0J ET0 → ~5″ backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Nissan spec, or want a wheel built to a custom offset for your Nissan Pathfinder? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Nissan Pathfinder use?
How many lug bolts does the Nissan Pathfinder use?
What is the center bore size on the Nissan Pathfinder?
What size are the factory (stock) wheels on the Nissan Pathfinder?
What is the biggest wheel size I can fit on my Nissan Pathfinder without rubbing?
What does a flush wheel fitment look like on the Nissan Pathfinder?
Do I need wheel spacers for my Nissan Pathfinder?
How do I calculate wheel backspacing for my Nissan Pathfinder?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Nissan Pathfinder?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.25, conical-seat lug nut.
Factory Torque Spec: 103-122 Nm (76-90 ft-lb). Range covers most Nissan passenger cars and crossovers on M12x1.25 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.