Brushed Silver 14-Spoke Forged Wheels
Monoblock · Brushed Silver
2011 Maybach 62 S Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Maybach 62 S wheels? This page gives the 2011 Maybach 62 S bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Maybach 62 S rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2011 Maybach 62 S uses a 5x112 bolt pattern with a 66.6 mm centre bore and M14x1.5 lug bolts. Factory wheels: 20x8.5J ET50. For aftermarket wheels, 21x9.5J ET35 sits flush.
Forged wheels for the 2011 Maybach 62 S — drilled 5x112 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Maybach 62 S (2011): 5x112 bolt pattern, 66.6mm center bore, OE 20x8.5J ET50. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore66.6mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2011
Category5-Lug Large Sedan/SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 20x8.5J ET50 |
| Flush Fitment | 21x9.5J at ET35 offset |
Forged Wheel Designs for the Maybach 62 S
Every design below is forged to order, so it can be machined to the Maybach 62 S's 5x112 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
BBS-Style Brushed Silver Mesh Polished-Lip Forged Wheels
Monoblock · Matte Silver
Wheelforce-Style Gunmetal 10 Directional-Spoke Forged Wheels
Replica · Gunmetal
Black / Machined 5-Spoke Forged Wheels
Monoblock · Black Machined
WF CF.4-FFR-Style Gloss Black 5 W-Spoke Forged Wheels
Replica · Gloss Black
Gloss Black 2-Piece Polished Deep Lip Riveted Forged Wheels
2-Piece · Gloss Black
Matte Black / Gunmetal Double-Ring Spoke Left/Right Directional Forged Wheels
Monoblock · Matte Black / Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Maybach 62 S ships from the factory on a 5x112 bolt pattern with a 66.6mm center bore and a 20x8.5J ET50 wheel. Our flush reference for the Maybach 62 S is 21x9.5J ET35.; our maximum aggressive reference is 22x10J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
Maybach 62 S OE Wheel Specs
The Maybach 62 S ships from the factory on 5x112 bolt pattern wheels with a 66.6mm center bore. The stock wheel size is 20x8.5J ET50, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Maybach 62 S (2011) we drill the 5x112 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 20x8.5J | ET50 | 6.72 in (171 mm) | — | — |
| Flush | 21x9.5J | ET35 | 6.63 in (168 mm) | −2 mm | +28 mm |
| Maximum | 22x10J | ET30 | 6.68 in (170 mm) | −1 mm | +39 mm |
Vehicles With the Same Hub as the Maybach 62 S (5x112, 66.6 mm Bore)
In our database, 823 other vehicle entries from 21 makes use exactly the same 5x112 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 58.6% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Maybach 62 S use?
The 2011 Maybach 62 S uses a 5x112 bolt pattern.
How many lug bolts does the Maybach 62 S use?
The Maybach 62 S uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Maybach 62 S?
The Maybach 62 S's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Maybach 62 S?
Factory wheels on the Maybach 62 S are 20x8.5J ET50.
What does a flush wheel fitment look like on the Maybach 62 S?
For a flush look with minimal to no rubbing, we recommend 21x9.5J at ET35 offset as a starting point on a stock or mildly lowered Maybach 62 S.
Do I need wheel spacers for my Maybach 62 S?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Maybach 62 S?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.63" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Maybach 62 S?
The Maybach 62 S runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 20x8.5 wheels · 20 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.