Maybach 57S Special (2005) Wheel Fitment

Maybach 57S Special (2005): 5x112 bolt pattern, 66.6mm center bore, OE 20x8.5J ET50. Forged wheel fitment specs from ANKUSI.

Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore66.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2005
Category5-Lug Performance / Tuner

Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →

Wheel Size & Offset at a Glance

Maybach 57S Special wheel size and offset comparison by configuration
ConfigurationWheel Size & Offset
Flush Fitment21x9.5J at ET35 offset

How to Read Wheel Offset & Measurements

Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.

Diagram showing wheel measurement points: centerline, center bore diameter, PCD, offset, rim width and diameter
Centerline, center bore, PCD, offset, width & diameter
Diagram comparing positive, zero, and negative wheel offset relative to the wheel centerline
Positive vs. zero vs. negative offset

ANKUSI Engineering Expert Advice

A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.

The Maybach 57S Special ships from the factory on a 5x112 bolt pattern with a 66.6mm center bore and a 20x8.5J ET50 wheel. Our flush reference for the Maybach 57S Special is 21x9.5J ET35.; our maximum aggressive reference is 22x10J ET30. — beyond that, expect clearance issues against the fender liner without further modification.

Maybach 57S Special OE Wheel Specs

The Maybach 57S Special ships from the factory on 5x112 bolt pattern wheels with a 66.6mm center bore. The stock wheel size is 20x8.5J ET50, offering a balanced ride that suits most owners without any rubbing or clearance concerns.

Why the factory spec works for most owners:

  • Balances ride comfort with steering response and highway efficiency.
  • Wide tire and wheel availability at the factory diameter keeps replacement costs low.
  • Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
  • Guaranteed clearance against brake calipers and suspension components.

Flush Fitment

For a flush look without any body modification, most Maybach 57S Special owners run 21x9.5J ET35. This setup tucks the wheel face closer to the fender lip while staying within safe load and clearance limits.

Maximum Aggressive Fitment

Owners chasing a more aggressive stance push to 22x10J ET30. Chassis: Factory sport-tuned air suspension; lowering links compatible. Brakes: Twin-caliper front clearance. Tires: 275/40 R20. Clearance should be verified before ordering, especially on lowered cars.

5-Tier Configuration Options

A – Factory-Style: 20x8.5J ET50

Recommended setup: Factory-matched forged replacement

Economy impact: None

Best for: Daily drivers, warranty-conscious owners

Appearance 5/10 | Comfort 10/10 | Install difficulty ★☆☆☆

Estimated cost range: $$ (OE replacement)

B – Comfortable Upgrade: 20.5x9J ET43

Recommended setup: Direct bolt-on, factory suspension

Economy impact: Minimal

Best for: Owners who want a mild upgrade with no compromise

Appearance 6/10 | Comfort 9/10 | Install difficulty ★☆☆☆

Estimated cost range: $$ - $$$

C – Balanced / Flush Fit: 21x9.5J ET35

Recommended setup: Flush forged wheels, stock or mild lowering

Economy impact: Slight increase

Best for: Enthusiasts wanting a flush look daily

Appearance 8/10 | Comfort 7/10 | Install difficulty ★★☆☆

Estimated cost range: $$$

D – Aggressive: 21.5x10J ET33

Recommended setup: Wider forged wheels, coilovers or lowering springs

Economy impact: Noticeable increase

Best for: Show-and-drive builds

Appearance 9/10 | Comfort 5/10 | Install difficulty ★★★☆

Estimated cost range: $$$$

E – Max Aggressive: 22x10J ET30

Recommended setup: Chassis: Factory sport-tuned air suspension; lowering links compatible. Brakes: Twin-caliper front clearance. Tires: 275/40 R20.

Economy impact: Significant increase

Best for: Show builds, weekend cars

Appearance 10/10 | Comfort 3/10 | Install difficulty ★★★★

Estimated cost range: $$$$$

Performance Comparison Matrix

Wheel SpecTier ATier BTier CTier DTier E
Wheel Spec20x8.5J ET5020.5x9J ET4321x9.5J ET3521.5x10J ET3322x10J ET30
Economy ImpactNoneMinimalSlight increaseNoticeable increaseSignificant increase
Appearance5/106/108/109/1010/10
Comfort10/109/107/105/103/10
Install Difficulty★☆☆☆★☆☆☆★★☆☆★★★☆★★★★
Cost Range$$ (OE replacement)$$ - $$$$$$$$$$$$$$$
Best ForDaily drivers, warranty-conscious ownersOwners who want a mild upgrade with no compromiseEnthusiasts wanting a flush look dailyShow-and-drive buildsShow builds, weekend cars

Real-World Reference Cases

The following builds are compiled from typical ANKUSI customer configurations for this platform and are illustrative, not individually verified real-world builds.

Case 1: Daily Driver (Factory-Style)

Profile: Commuter prioritizing comfort and reliability.

Setup: 20x8.5J ET50 forged wheels, factory suspension.

Cost: $$ (OE replacement)

Outcome: No clearance issues, factory ride quality retained.

Case 2: Balanced Enthusiast (Balanced / Flush Fit)

Profile: Weekend driver wanting a flush stance without sacrificing daily usability.

Setup: 21x9.5J ET35 forged wheels, mild lowering springs.

Cost: $$$

Outcome: Flush fitment with acceptable ride comfort for daily use.

Case 3: Show Build (Max Aggressive)

Profile: Show-and-shine build prioritizing stance over comfort.

Setup: 22x10J ET30 forged wheels. Chassis: Factory sport-tuned air suspension; lowering links compatible. Brakes: Twin-caliper front clearance. Tires: 275/40 R20.

Cost: $$$$$

Outcome: Maximum aggressive stance; clearance verified case-by-case.

Decision Guide

1. What is this car mainly used for? Daily driving favors Tier A or B; weekend/show use favors Tier D or E.
2. What is your budget? Tiers A-B keep cost low; Tiers D-E cost significantly more in wheels, tires, and possible suspension work.
3. Is fuel economy and ride comfort a priority? If yes, stay at Tier A or B; heavier, wider wheels at Tier D-E reduce efficiency and comfort.
4. Still unsure? Tier C (Balanced / Flush Fit) is the safe default for most Maybach 57S Special owners.

Offset & Backspacing Reference

Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.

  • OE 20x8.5J ET50: backspacing ≈ 6.72"
  • Flush 21x9.5J ET35: backspacing ≈ 6.63"
  • Max 22x10J ET30: backspacing ≈ 6.68"

Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Maybach 57S Special.

Frequently Asked Questions

What bolt pattern (PCD) does the Maybach 57S Special use?
The 2005 Maybach 57S Special uses a 5x112 bolt pattern.
How many lug bolts does the Maybach 57S Special use?
The Maybach 57S Special uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What does a flush wheel fitment look like on the Maybach 57S Special?
For a flush look with minimal to no rubbing, we recommend 21x9.5J at ET35 offset as a starting point on a stock or mildly lowered Maybach 57S Special.
Do I need wheel spacers for my Maybach 57S Special?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Maybach 57S Special?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.63" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Maybach 57S Special?
The Maybach 57S Special runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.

← Back to the full Fitment Guide · Browse forged wheels

Contact WhatsApp Get a Quote