2025 MG HS Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting MG HS wheels? This page gives the 2025 MG HS bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged MG HS rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 MG HS uses a 5x112 bolt pattern with a 66.6 mm centre bore and M12x1.5 lug nuts. For aftermarket wheels, 20x8.5J ET35 sits flush.
Forged wheels for the 2025 MG HS — drilled 5x112 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
MG HS (2025) wheel fitment guide: 5x112 bolt pattern, 66.6mm center bore, factory 19x7J ET38 wheels. Flush and aggressive forged wheel fitment specs from ANKUSI.
Bolt Pattern5x112
Wheel Bolt/NutM12x1.5 Nut
Center Bore66.6mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2025
Category5-Lug Large Sedan/SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | 20x8.5J at ET35 offset |
Forged Wheel Designs for the MG HS
Every design below is forged to order, so it can be machined to the MG HS's 5x112 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
Metallic Gray Multi-Spoke Machined Face Forged Wheels
Monoblock · Metallic Gray
Vossen HF-2-Style Gloss Black 10 Y-Spoke Forged Wheels
Replica · Gloss Black
Black / Machined 5-Spoke Machined Face Forged Wheels
Monoblock · Black Machined
Brushed Silver Lettered 20-Spoke Forged Wheels
Monoblock · Matte Silver
HRE P200-Style Silver 12 Y-Spoke Forged Wheels
Replica · Silver
Black / Machined Split Machined Face Forged Wheels
Monoblock · Black Machined
WF Gold 5 Y-Spoke Directional Forged Wheels
Replica · Gold
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The MG HS ships from the factory on a 5x112 bolt pattern with a 66.6mm center bore and a 19x7J ET38 wheel. Our flush reference for the MG HS is 20x8.5J ET35.; our maximum aggressive reference is 21x9J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
MG HS OE Wheel Specs
The MG HS ships from the factory on 5x112 bolt pattern wheels with a 66.6mm center bore. The stock wheel size is 19x7J ET38, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the MG HS (2025) we drill the 5x112 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
- OE 19x7J ET38: backspacing ≈ 5.50"
- Flush 20x8.5J ET35: backspacing ≈ 6.13"
- Max 21x9J ET30: backspacing ≈ 6.18"
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your MG HS.
Vehicles With the Same Hub as the MG HS (5x112, 66.6 mm Bore)
In our database, 823 other vehicle entries from 21 makes use exactly the same 5x112 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 58.6% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the MG HS use?
The 2025 MG HS uses a 5x112 bolt pattern.
How many lug bolts does the MG HS use?
The MG HS uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the MG HS?
The MG HS's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the MG HS?
For a flush look with minimal to no rubbing, we recommend 20x8.5J at ET35 offset as a starting point on a stock or mildly lowered MG HS.
Do I need wheel spacers for my MG HS?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my MG HS?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.13" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my MG HS?
The MG HS runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.