Chrysler 300 Forged Wheels
Replica
2007 Chrysler Crossfire (UK) Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Chrysler Crossfire (UK) wheels? This page gives the 2007 Chrysler Crossfire (UK) bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Chrysler Crossfire (UK) rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2007 Chrysler Crossfire (UK) uses a 5x112 bolt pattern with a 66.5 mm centre bore and M12x1.5 lug nuts. Factory wheels: F: 18x7.5J R: 19x9J. For aftermarket wheels, 19x8.5J ET30 front / 20x10J ET20 rear sits flush and 19x9J ET25 front / 20x10.5J ET15 rear is the most aggressive fit.
Forged wheels for the 2007 Chrysler Crossfire (UK) — drilled 5x112 with a 66.5 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Chrysler Crossfire (UK) (2007): 5x112 bolt pattern, 66.5mm center bore. Factory wheels: F: 18x7.5J R: 19x9J. Reference fitment ranges.
Bolt Pattern5x112
Wheel Bolt/NutM12x1.5 Nut
Center Bore66.5mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2007
CategoryCoupe
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 18x7.5J R: 19x9J |
| Flush Fitment | F 19x8.5J ET30 / R 20x10J ET20 |
| Maximum Aggressive | F 19x9J ET25 / R 20x10.5J ET15 |
Forged Wheel Designs for the Chrysler Crossfire (UK)
Every design below is forged to order, so it can be machined to the Chrysler Crossfire (UK)'s 5x112 bolt pattern and 66.5 mm center bore, with the width and offset calculated for your setup.
Chrysler OEM-Style Gunmetal / Machined Split Forged Wheels
Monoblock · Gunmetal / Machined
Gloss Black 10-Spoke Forged Wheels
Monoblock · Gloss Black
BMW M3 CS Handschalter Forged Wheels
Monoblock
Chrysler OEM-Style Polished 5-Spoke Forged Wheels
Monoblock · Polished
Rays-Style Gloss Black 6-Spoke Forged Wheels
Monoblock · Gloss Black
Vossen-Style Gloss Black 5 Y-Split-Spoke Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Coupes and performance platforms are where rotational mass shows up fastest — in acceleration, in braking, and in how quickly the chassis changes direction. Forging lets us build to the same strength spec as the factory wheel at a meaningfully lower rotational weight, which is where the performance gain actually comes from, not just the visual one.
The Chrysler Crossfire (UK) runs a 5x112 bolt pattern, 66.5mm center bore, and a F: 18x7.5J wheel from the factory. Our Flush Fitment reference is F 19x8.5J ET30 / R 20x10J ET20, which tucks the tire under the fender lip on a stock-height Chrysler Crossfire (UK). Our Maximum Aggressive reference is F 19x9J ET25 / R 20x10.5J ET15 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Chrysler Crossfire (UK) OE Wheel Specs
The 2007 Chrysler Crossfire (UK) (Coupe) uses a 5x112 bolt pattern with a 66.5mm center bore. Factory wheels are F: 18x7.5J R: 19x9J.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Chrysler Crossfire (UK) (2007) we drill the 5x112 pattern and cut the centre bore to 66.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
KW V2 coilovers; 19/20-inch Forgeline wheels; Brembo 4-piston brakes; Michelin Pilot Sport 4S (F: 225/35 R19, R: 275/30 R20).
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 18x7.5J ET35 → ~5.63″ F backspacing, R 19x9J ET22 → ~5.87″ R backspacing
- Flush: F 19x8.5J ET30 → ~5.93″ F backspacing, R 20x10J ET20 → ~6.29″ R backspacing
- Max: F 19x9J ET25 → ~5.98″ F backspacing, R 20x10.5J ET15 → ~6.34″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Chrysler spec, or want a wheel built to a custom offset for your Chrysler Crossfire (UK)? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Chrysler Crossfire (UK) (5x112, 66.5 mm Bore)
In our database, 167 other vehicle entries from 6 makes use exactly the same 5x112 bolt pattern and 66.5 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 11.9% of those also use a 66.5 mm center bore.
Hub-Centric Rings for a 66.5 mm Center Bore
A wheel with a center bore larger than 66.5 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.6 mm | 66.6 → 66.5 mm |
| 67.1 mm | 67.1 → 66.5 mm |
| 70.1 mm | 70.1 → 66.5 mm |
| 70.5 mm | 70.5 → 66.5 mm |
| 73.1 mm | 73.1 → 66.5 mm |
ANKUSI forged wheels are bored to exactly 66.5 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Chrysler Crossfire (UK) use?
The 2007 Chrysler Crossfire (UK) uses a 5x112 bolt pattern.
How many lug bolts does the Chrysler Crossfire (UK) use?
The Chrysler Crossfire (UK) uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Chrysler Crossfire (UK)?
The Chrysler Crossfire (UK)'s center bore is 66.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Chrysler Crossfire (UK)?
Factory wheels on the Chrysler Crossfire (UK) are F: 18x7.5J R: 19x9J.
What is the biggest wheel size I can fit on my Chrysler Crossfire (UK) without rubbing?
The most aggressive fitment we recommend without fender work is F 19x9J ET25 / R 20x10.5J ET15. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Chrysler Crossfire (UK)?
For a flush look with minimal to no rubbing, we recommend F 19x8.5J ET30 / R 20x10J ET20 as a starting point on a stock or mildly lowered Chrysler Crossfire (UK).
Do I need wheel spacers for my Chrysler Crossfire (UK)?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Chrysler Crossfire (UK)?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.93" backspacing up front and 6.29" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Chrysler Crossfire (UK)?
Yes — the Chrysler Crossfire (UK)'s factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x7.5 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.