
HRE-Style Bronze 5 Y-Spoke Forged Wheels
Monoblock · Bronze
Fitting Porsche Macan Turbo wheels? This page gives the 2019 Porsche Macan Turbo bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Porsche Macan Turbo rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche Macan Turbo (2019): 5x112 bolt pattern, 66.5mm center bore. Factory wheels: F: 20x9J R: 20x10J. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 20x9J R: 20x10J |
| Flush Fitment | F 21x9.5J ET26 / R 21x11J ET19 |
| Maximum Aggressive | F 21x9.5J ET26 / R 21x11J ET19 |
Every design below is forged to order, so it can be machined to the Porsche Macan Turbo's 5x112 bolt pattern and 66.5 mm center bore, with the width and offset calculated for your setup.

Monoblock · Bronze

Deep Dish · Matte Silver

Replica · Gunmetal

Replica · Bronze

Monoblock · Silver

Monoblock · Gloss White

Monoblock · Gloss Black / Machined

Replica · Gunmetal
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a vehicle this heavy, the wheel is a structural part before it is a styling part - it carries the load, the brake heat and the cornering forces all at once. A forged wheel buys back unsprung weight without giving up the load rating an SUV actually needs, which is the one number most cast aftermarket wheels quietly fall short on.
The Porsche Macan Turbo runs a 5x112 fitment, 66.5mm center bore, and a F: 20x9J wheel from the factory. Our Flush Fitment reference is F 21x9.5J ET26 / R 21x11J ET19, which tucks the tire under the fender lip on a stock-height Porsche Macan Turbo. Our Maximum Aggressive reference is F 21x9.5J ET26 / R 21x11J ET19 - the verified data does not support going wider than the flush spec on this chassis.
The 2019 Porsche Macan Turbo (Crossover) uses a 5x112 bolt pattern with a 66.5mm center bore. Factory wheels are F: 20x9J R: 20x10J.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche Macan Turbo (2019) we drill the 5x112 pattern and cut the centre bore to 66.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
LFI 21x9.5/21x11 and RP21-style 21x10 ET19 are common; if running spacers use extended lug bolts 95B uses 5x112 / M14x1.5 with OE R14 BALL-seat lug geometry - aftermarket conical-seat wheels/spacers need matching conical bolts, do not reuse OE ball-seat bolts. Verified at 95B Turbo/GTS platform level (LFI / ECS / Pelican).
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche Macan Turbo? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.