G80 M3 Wheel Fitment: Forged Upgrade Sizes, Offsets and Brake Clearance (2026)

Vehicle FitmentPublished By ANKUSI Engineering Team
G80 M3 wheel fitment reference: BMW M3 Competition sedan on factory 19-inch front and 20-inch rear wheels

G80 M3 wheel fitment starts from three fixed numbers: a 5x112 bolt pattern, a 66.6 mm center bore and M14x1.25 lug bolts, with ET20 factory offsets at all four corners. Those figures, listed on our BMW M3 Competition G80 fitment page, are the same for the G82 M4. The real decisions are which diameter, width and offset to order once you move past the factory 18/19-inch or 19/20-inch setup.

This G80 M3 wheel fitment guide does not repeat the full spec sheet. It explains how a forged upgrade changes the position of the wheel, which sizes wheel specialists publish for the G8x chassis, how brakes limit your choices, and why F80 and F82 wheels will not carry over.

Key facts: G80 M3 and G82 M4 wheels in three lines

  • Hub and hardware: 5x112 bolt pattern, 66.6 mm center bore (66.56 mm before rounding) and M14x1.25 lug bolts, per a BMW bolt pattern and bore guide, a US fitment database and a wheel maker's G8x fitment page. The F80 M3 and F82 M4 used 5x120 and a 72.6 mm bore, so older wheels do not bolt on.
  • Factory offset: every corner is ET20. The base car runs 18x9.5 front and 19x10.5 rear; Competition models run 19x9.5 front and 20x10.5 rear (the US fitment database, Koleso.ee, BimmerWorld).
  • Upgrade math: going from the Competition front 19x9.5 ET20 to a 19x10 ET12 pushes the outer lip out 14.4 mm, while the inner barrel moves 1.7 mm away from the strut.
G80 M3 wheel fitment reference: BMW M3 Competition sedan on factory 19-inch front and 20-inch rear wheels
A G80 M3 Competition on its factory staggered wheels: 19x9.5 ET20 at the front and 20x10.5 ET20 at the rear.

Factory G80 M3 and G82 M4 wheel sizes

All factory G80 M3 and G82 M4 wheels share one offset, ET20, so every aftermarket size can be compared against a single reference point. Only the diameter and width change between the base car and the Competition. The table below is the baseline for every G80 M3 wheel fitment calculation in this guide, and G82 M4 wheel fitment follows the same numbers.

ModelFront wheelFront tireRear wheelRear tire
M3 / M4 (base)18x9.5 ET20275/40R1819x10.5 ET20285/35R19
M3 / M4 Competition and Competition xDrive19x9.5 ET20275/35R1920x10.5 ET20285/30R20

Sources: the US fitment database (2025 M3 by trim), Koleso.ee (base M3), Tire Wheel Guide (2021 M4) and BimmerWorld (rear 20x10.5 ET20 shared by the G87 M2, G80 M3 and G82 M4). Year-by-year data lives on our M4 Competition G82 page and the BMW M3 bolt pattern hub.

A note on the bore: some catalogs print 66.5 mm and others 66.6 mm. The wheel maker's G8x page lists the unrounded figure, 66.56 mm, which explains the split. A wheel machined to 66.6 mm fits either way.

How width and offset change G80 M3 wheel fitment

Every change in width or offset moves the outer lip and the inner barrel by predictable amounts. Half of any extra width goes to each side of the wheel, and each millimeter of lower offset shifts the whole wheel outward by one millimeter. The table applies that rule to sizes published in a BMW wheel specialist's G80 guide and a wheel maker's G8x spec, both linked below.

AxleFrom (factory)ToOuter lip movesInner barrel movesSource
Front19x9.5 ET2019x10 ET1214.4 mm out1.7 mm away from strutSpecialist guide
Front19x9.5 ET2020x10 ET1511.4 mm out1.4 mm toward strutMaker's G8x spec
Front19x9.5 ET2020x10 ET818.4 mm out5.7 mm away from strutSpecialist guide
Rear20x10.5 ET2020x11 ET188.4 mm out4.4 mm toward suspensionSpecialist guide
Rear20x10.5 ET2020x11 ET1511.4 mm out1.4 mm toward suspensionMaker's G8x spec

Calculated by the ANKUSI engineering team: half the width change (0.5 inch = 12.7 mm, so 6.35 mm per side) plus or minus the offset change. Our offset and backspacing calculator runs the same math for any other size.

Published advice differs on how far to go. A BMW wheel specialist's G80 M3 fitment guide (the "specialist guide" in the table) lists 19x10 ET12 as a bolt-on street size, while CenCal Motorsport warns that a front offset below ET18 can rub the inner liner at full lock. Treat the lower offsets as a starting point for a test fit rather than a guaranteed bolt-on size.

Published G80 M3 wheel fitment upgrades fall into three groups: an OEM-plus staggered setup, a square setup that allows tire rotation, and a 20-inch setup at both ends. The sizes below come from published fitment guides, not from customer builds.

  • OEM-plus staggered: 19x10 ET12 front with 20x11 ET18 rear on 285/35R19 and 305/30R20 tires (specialist guide).
  • Square 19-inch: 19x10 ET12 on all four corners with 275/35R19 or 285/35R19 tires (specialist guide). Square sizes let you rotate tires front to rear.
  • 20-inch at both ends: 20x10 ET15 front and 20x11 ET15 rear on 285/30R20 and 295/30R20 tires; the maker's G8x spec notes that a 305/30R20 rear works on rear-drive cars and that front rubbing depends on the tire sidewall.

Tire size changes the rolling diameter too. The factory Competition front tire, 275/35R19, measures about 675.1 mm across; a 285/35R19 is about 682.1 mm (+1.0%), and a 285/30R20 is about 679.0 mm. At the rear, 295/30R20 is about 685.0 mm against the factory 285/30R20 at 679.0 mm.

If you want G80 M3 forged wheels that keep a factory-style look in these sizes, the gunmetal machined 7-spoke forged wheel and the matte bronze split 5-spoke concave forged wheel are both made with a BMW center cap and drilled 5x112.

BMW OEM-Style Matte Bronze 5 Y-Spoke Concave Forged Wheels, angled view of the concave face
A matte bronze concave forged wheel with a BMW center cap, made to order in 5x112 for the G80 M3 and G82 M4.View this wheel ↗

Brake clearance: carbon ceramics and 18-inch wheels

Brakes can rule out a size before the fender does, so check them first when planning G80 M3 wheel fitment. The specialist guide lists 19 inches as the minimum diameter for cars with M carbon ceramic brakes, and its 18x10.5 setups are marked for steel brakes only.

Front 20-inch wheel of a BMW M4 Competition M xDrive (G82) with the gold carbon ceramic brake caliper visible through the spokes
A G82 M4 Competition with M carbon ceramic brakes: the gold caliper sits close to the spokes, which is why diameter and spoke profile matter.

Spoke profile matters as much as diameter, because the back of a concave spoke sits closer to the caliper than a flat one. A caliper template check before machining is the safe route. Our forged wheel fitment checklist lists the measurements to send.

Planning forged wheels for your M3 or M4? ANKUSI forged wheels start from $231 per wheel and are machined to your bolt pattern, bore and offset. Production takes 18–22 days and sea freight takes 30–35 days. Send your model, brake package and target sizes for a drawing and quote.

Will F80 M3 or G87 M2 wheels fit a G80 M3?

F80 M3 and F82 M4 wheels do not fit a G80 M3 or G82 M4 without adapters: the bolt circle changed from 5x120 to 5x112 and the bore shrank from 72.6 mm to 66.6 mm. G87 M2 wheels share the 5x112 pattern and 66.6 mm bore, and BimmerWorld lists one 20x10.5 ET20 factory rear wheel used on all three cars.

ChassisBolt patternCenter boreBolts onto a G80 M3?
F80 M3 / F82 M4 (2014–2020)5x12072.6 mmNo, the bolt circle differs
G80 M3 / G82 M4 (2021–)5x11266.6 mmYes
G87 M2 (2023–)5x11266.6 mmBolt pattern and bore match; check width and offset

See the F80 M3 fitment page, the G87 M2 page and our BMW M bolt pattern guide for every chassis. The BMW bolt pattern guide cited above lists the F80 at 5x120 with a 72.56 mm bore, and Tire Wheel Guide gives the 2023 M2 the same 19x9.5 and 20x10.5 ET20 factory sizes as the M3 Competition.

BMW M4 coupe (G82) in white on black factory M wheels, front three-quarter view
The G82 M4 coupe uses the same 5x112 hub, 66.6 mm bore and ET20 factory offsets as the G80 M3 sedan.

Hub rings, bolts and the details that decide a good fit

A forged wheel bored to 66.6 mm centers on the G80 hub with no ring. Many off-the-shelf wheels are bored larger to cover more cars; CenCal mentions 72.6 mm and 74.1 mm bores, which need rings with a 3.0 mm and 3.75 mm wall respectively. Our guide to hub-centric vs lug-centric wheels explains why the fit matters.

The lug bolts need the same attention. The G80 uses M14x1.25 bolts, and BMW specialist sources list a 60-degree cone seat for the factory bolts. Any spacer adds length, so the bolts must be longer by the spacer thickness. Our lug seat guide shows how to check the seat on the wheel itself.

Finally, decide on construction, the last choice in any G80 M3 wheel fitment plan. A monoblock wheel suits a weight-focused track build, while a two-piece wheel such as the gunmetal mesh 2-piece forged wheel with a polished lip or the brushed silver multi-spoke 2-piece forged wheel lets you fine-tune lip depth. Our monoblock vs 2-piece comparison covers the trade-offs, and the 5x112 bolt pattern page lists other cars that share this hub.

BMW OEM-Style Gunmetal Machined 7-Spoke Forged Wheels, front view

Gunmetal Machined 7-Spoke

Get a quote

BMW OEM-Style Matte Bronze 5 Y-Spoke Concave Forged Wheels, front view

Matte Bronze Split 5-Spoke Concave

Get a quote

BMW OEM-Style 2-Piece Gunmetal Mesh Riveted Polished Lip Forged Wheels, front view

2-Piece Gunmetal Mesh, Polished Lip

Get a quote

BMW OEM-Style Brushed Silver Multi-Spoke Riveted Deep Lip Forged Wheels, front view

2-Piece Brushed Silver Multi-Spoke, Deep Lip

Get a quote

Browse more M3 designs on our BMW M3 forged wheels page or the two-piece forged wheel collection.

Frequently Asked Questions

What offset do factory G80 M3 wheels use?

Every factory G80 M3 wheel is ET20. The base car uses 18x9.5 front and 19x10.5 rear wheels, while the Competition and Competition xDrive use 19x9.5 front and 20x10.5 rear, all at ET20.

Do F80 M3 wheels fit a G80 M3?

No. The F80 M3 and F82 M4 use a 5x120 bolt pattern with a 72.6 mm center bore, while the G80 M3 and G82 M4 use 5x112 with a 66.6 mm bore, so F80 wheels do not bolt on without adapters.

Can a G80 M3 run 18-inch wheels?

Only with steel brakes and a design that clears the calipers. Apex lists 19 inches as the minimum diameter for cars with M carbon ceramic brakes and marks its 18x10.5 setups for steel brakes only.

Do I need hub rings on a G80 M3?

Not if the wheel is bored to 66.6 mm. Wheels with a larger 72.6 mm or 74.1 mm bore need hub-centric rings with a 3.0 mm or 3.75 mm wall to center on the G80 hub.

Is G82 M4 wheel fitment the same as the G80 M3?

Yes. The G82 M4 shares the 5x112 bolt pattern, 66.6 mm center bore, M14x1.25 lug bolts and the same ET20 factory wheel sizes, so a wheel that fits a G80 M3 also fits the G82 M4.

Technical Inquiry

Need answers from the manufacturing side instead of just sales copy?

Contact ANKUSI through WhatsApp or WeChat for discussions on forged wheel customization, fitment, finishes, and project feasibility.

Don't see exactly what you want?We can custom-forge any size, style, color, or finish.
Contact WhatsApp Get a Quote