HRE-Style Gunmetal 10 V-Spoke Deep Lip 2-Piece Forged Wheels
2-Piece · Gunmetal
2014 Porsche Panamera Turbo S Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche Panamera Turbo S wheels? This page gives the 2014 Porsche Panamera Turbo S bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche Panamera Turbo S rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche Panamera Turbo S (2014): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 20x9.5J R: 20x11J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Caliper TypeFixed 6-piston front caliper (OEM, Porsche Turbo)
Year2014
CategoryPerformance Sedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 20x9.5J R: 20x11J |
| Flush Fitment | F 21x9.5J ET55 / R 21x11J ET48 |
| Maximum Aggressive | F 22x10J ET40 / R 22x11.5J ET48 |
Forged Wheel Designs for the Porsche Panamera Turbo S
Every design below is forged to order, so it can be machined to the Porsche Panamera Turbo S's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
HRE P161SC-Style Silver 5 Y-Spoke Forged Wheels
Replica · Silver
Porsche 911 Turbo S Forged Wheels
Monoblock
BBS LM-Style Matte Silver Forged Wheels
Replica · Matte Silver
HRE P101-Style Gray 5 Y-Spoke Polished Forged Wheels
Replica · Gray
Gloss Black 5 Y-Spoke Red Lip Concave Forged Wheels
Concave · Gloss Black
Porsche OEM-Style Matte Black 5 Split-Spoke Forged Wheels
Monoblock · Gloss Black
See all Porsche Panamera wheel designs Porsche OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A big saloon lives or dies on ride quality, and the wheel is the first thing that ruins it. Going wider and lower without watching load rating and offset trades away exactly the composure you paid for. Forging lets you add diameter and width while keeping rotating mass close to the factory figure.
The Porsche Panamera Turbo S runs a 5x130 fitment, 71.6mm center bore, and a F: 20x9.5J wheel from the factory. Our Flush Fitment reference is F 21x9.5J ET55 / R 21x11J ET48, which tucks the tire under the fender lip on a stock-height Porsche Panamera Turbo S. Our Maximum Aggressive reference is F 22x10J ET40 / R 22x11.5J ET48 - beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Porsche Panamera Turbo S OE Wheel Specs
The 2014 Porsche Panamera Turbo S (Performance Sedan) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 20x9.5J R: 20x11J.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche Panamera Turbo S (2014) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
Turbo S on 22in HRE/Vossen/Vorsteiner forged or flow-formed with air-lowering module; keep load rating verified via Vorsteiner V-FF107 / Vossen HF-5 970 Panamera product data
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 20x9.5J ET65 → ~7.81″ F backspacing, R 20x11J ET65 → ~8.56″ R backspacing
- Flush: F 21x9.5J ET55 → ~7.42″ F backspacing, R 21x11J ET48 → ~7.89″ R backspacing
- Max: F 22x10J ET40 → ~7.07″ F backspacing, R 22x11.5J ET48 → ~8.14″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche Panamera Turbo S? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Porsche Panamera Turbo S use?
The 2014 Porsche Panamera Turbo S uses a 5x130 bolt pattern.
How many lug bolts does the Porsche Panamera Turbo S use?
The Porsche Panamera Turbo S uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche Panamera Turbo S?
The Porsche Panamera Turbo S's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche Panamera Turbo S?
Factory wheels on the Porsche Panamera Turbo S are F: 20x9.5J R: 20x11J.
What is the biggest wheel size I can fit on my Porsche Panamera Turbo S without rubbing?
The most aggressive fitment we recommend without fender work is F 22x10J ET40 / R 22x11.5J ET48. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche Panamera Turbo S?
For a flush look with minimal to no rubbing, we recommend F 21x9.5J ET55 / R 21x11J ET48 as a starting point on a stock or mildly lowered Porsche Panamera Turbo S.
Do I need wheel spacers for my Porsche Panamera Turbo S?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche Panamera Turbo S?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 7.42" backspacing up front and 7.89" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche Panamera Turbo S?
Yes — the Porsche Panamera Turbo S's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.