
Matte Silver 5 Y-Spoke Deep Lip Forged Wheels
Deep Dish · Matte Silver
Fitting Porsche Macan wheels? This page gives the 2015 Porsche Macan bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Porsche Macan rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche Macan (2015): 5x112 bolt pattern, 66.5mm center bore. Factory wheels: F: 18x8J R: 18x9J. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 18x8J R: 18x9J |
| Flush Fitment | F 21x9J ET26 / R 21x10J ET19 |
| Maximum Aggressive | F 22x9J ET21 / R 22x10.5J ET19 |
Every design below is forged to order, so it can be machined to the Porsche Macan's 5x112 bolt pattern and 66.5 mm center bore, with the width and offset calculated for your setup.

Deep Dish · Matte Silver

2-Piece · Mirror Polished

Monoblock

2-Piece · Black / Silver

Deep Dish · Gold

Monoblock · Bronze

Concave · Gloss Black

2-Piece · Brushed Gold / Polished Lip
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a vehicle this heavy, the wheel is a structural part before it is a styling part - it carries the load, the brake heat and the cornering forces all at once. A forged wheel buys back unsprung weight without giving up the load rating an SUV actually needs, which is the one number most cast aftermarket wheels quietly fall short on.
The Porsche Macan runs a 5x112 fitment, 66.5mm center bore, and a F: 18x8J wheel from the factory. Our Flush Fitment reference is F 21x9J ET26 / R 21x10J ET19, which tucks the tire under the fender lip on a stock-height Porsche Macan. Our Maximum Aggressive reference is F 22x9J ET21 / R 22x10.5J ET19 - beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2015 Porsche Macan (Crossover) uses a 5x112 bolt pattern with a 66.5mm center bore. Factory wheels are F: 18x8J R: 18x9J.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche Macan (2015) we drill the 5x112 pattern and cut the centre bore to 66.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
95B Macan on 21-22in flow-formed/forged (HRE, Vossen, TSW) with lowering springs or air-lowering; 5x112 66.6 hubcentric 5x112 (ICE Macan) - do NOT confuse with 5x130 EV Macan. Verified at 95B platform level (bolt pattern & arches unchanged across 95B trims/years)
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche Macan? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.