
Advan-Style Bronze 5-Spoke Forged Wheels
Monoblock · Bronze
Fitting Porsche Macan Turbo with Performance Package wheels? This page gives the 2017 Porsche Macan Turbo with Performance Package bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Porsche Macan Turbo with Performance Package rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche Macan Turbo with Performance Package (2017): 5x112 bolt pattern, 66.5mm center bore. Factory wheels: F: 20x9J R: 20x10J. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 20x9J R: 20x10J |
| Flush Fitment | F 21x9.5J ET18 / R 21x10.5J ET15 |
| Maximum Aggressive | F 21x9.5J ET18 / R 21x10.5J ET15 |
Every design below is forged to order, so it can be machined to the Porsche Macan Turbo with Performance Package's 5x112 bolt pattern and 66.5 mm center bore, with the width and offset calculated for your setup.

Monoblock · Bronze

Monoblock · Chrome

2-Piece · Satin Black

Monoblock · Gunmetal

2-Piece · Silver

Monoblock · Black / White

Concave · Gold

Monoblock · Gunmetal
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


On a vehicle this heavy, the wheel is a structural part before it is a styling part - it carries the load, the brake heat and the cornering forces all at once. A forged wheel buys back unsprung weight without giving up the load rating an SUV actually needs, which is the one number most cast aftermarket wheels quietly fall short on.
The Porsche Macan Turbo with Performance Package runs a 5x112 fitment, 66.5mm center bore, and a F: 20x9J wheel from the factory. Our Flush Fitment reference is F 21x9.5J ET18 / R 21x10.5J ET15, which tucks the tire under the fender lip on a stock-height Porsche Macan Turbo with Performance Package. Our Maximum Aggressive reference is F 21x9.5J ET18 / R 21x10.5J ET15 - the verified data does not support going wider than the flush spec on this chassis.
The 2017 Porsche Macan Turbo with Performance Package (Crossover) uses a 5x112 bolt pattern with a 66.5mm center bore. Factory wheels are F: 20x9J R: 20x10J.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche Macan Turbo with Performance Package (2017) we drill the 5x112 pattern and cut the centre bore to 66.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
95B Macan builds run APEX VS-5RX or HRE/Vossen forged, H&R lowering springs or air links, Michelin PS4/Latitude Sport 5x112 (NOT 5x130 like most Porsches), CB 66.6; verified on APEX 95B Macan guide
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche Macan Turbo with Performance Package? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.