Jaguar OEM-Style Silver / Gloss Black Machined Face Forged Wheels
Monoblock · Silver / Gloss Black
2012 Jaguar XKR-S Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Jaguar XKR-S wheels? This page gives the 2012 Jaguar XKR-S bolt pattern (5x108), centre bore, factory rim size and the offset range for aftermarket and forged Jaguar XKR-S rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2012 Jaguar XKR-S uses a 5x108 bolt pattern with a 63.4 mm centre bore and M12x1.5 lug nuts. For aftermarket wheels, 20x9.5J ET40 front / 20x11J ET38 rear sits flush.
Forged wheels for the 2012 Jaguar XKR-S — drilled 5x108 with a 63.4 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Jaguar XKR-S (2012): 5x108 bolt pattern, 63.4mm center bore, OE F 20x9J ET49 / R 20x10.5J ET46. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x108
Wheel Bolt/NutM12x1.5 Nut
Center Bore63.4mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2012
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 20x9.5J ET40 / R 20x11J ET38 |
Forged Wheel Designs for the Jaguar XKR-S
Every design below is forged to order, so it can be machined to the Jaguar XKR-S's 5x108 bolt pattern and 63.4 mm center bore, with the width and offset calculated for your setup.
Jaguar OEM-Style Transparent Copper 10 Y-Spoke Side-Milled Forged Wheels
Monoblock · Transparent Copper
Brox-Style Matte Black 16-Spoke Machined Beadlock Off-Road Forged Wheels
Off-Road Beadlock · Matte Black / Machined
BMW M3 CS Handschalter Forged Wheels
Monoblock
Transparent Gray 10 Y-Spoke Concave Forged Wheels
Concave · Transparent Gray
Jaguar OEM-Style Gunmetal Machined Multi-Spoke Forged Wheels
Monoblock · Gunmetal / Machined
Jaguar OEM-Style Side-Milled Transparent Bronze 10 Y-Spoke Forged Wheels
Monoblock · Side-milled Transparent Bronze
Jaguar OEM-Style Gloss Black Machined Full-Face 5-Spoke Forged Wheels
Monoblock · Gloss Black / Machined
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The Jaguar XKR-S ships from the factory on a 5x108 bolt pattern with a 63.4mm center bore and a F 20x9J ET49 / R 20x10.5J ET46 wheel. Our flush reference for the Jaguar XKR-S is F 20x9.5J ET40 / R 20x11J ET38.; our maximum aggressive reference is F 21x10J ET35 / R 21x11.5J ET35. — beyond that, expect clearance issues against the fender liner without further modification.
Jaguar XKR-S OE Wheel Specs
The Jaguar XKR-S ships from the factory on 5x108 bolt pattern wheels with a 63.4mm center bore. The stock wheel size is F 20x9J ET49 / R 20x10.5J ET46, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Jaguar XKR-S (2012) we drill the 5x108 pattern and cut the centre bore to 63.4mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 20x9J | ET49 | 6.93 in (176 mm) | — | — |
| Flush | 20x9.5J | ET40 | 6.82 in (173 mm) | −3 mm | +15 mm |
| Maximum | 21x10J | ET35 | 6.88 in (175 mm) | −1 mm | +27 mm |
Vehicles With the Same Hub as the Jaguar XKR-S (5x108, 63.4 mm Bore)
In our database, 278 other vehicle entries from 17 makes use exactly the same 5x108 bolt pattern and 63.4 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x108 is used by 7.7% of the vehicle pages in our English fitment guide (499 of 6,503); 55.9% of those also use a 63.4 mm center bore.
Hub-Centric Rings for a 63.4 mm Center Bore
A wheel with a center bore larger than 63.4 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 64.1 mm | 64.1 → 63.4 mm |
| 65.1 mm | 65.1 → 63.4 mm |
| 66.1 mm | 66.1 → 63.4 mm |
| 66.6 mm | 66.6 → 63.4 mm |
| 73.1 mm | 73.1 → 63.4 mm |
ANKUSI forged wheels are bored to exactly 63.4 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Jaguar XKR-S use?
The 2012 Jaguar XKR-S uses a 5x108 bolt pattern.
How many lug bolts does the Jaguar XKR-S use?
The Jaguar XKR-S uses a 5-lug bolt pattern (5x108), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Jaguar XKR-S?
The Jaguar XKR-S's center bore is 63.4mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Jaguar XKR-S?
For a flush look with minimal to no rubbing, we recommend F 20x9.5J ET40 / R 20x11J ET38 as a starting point on a stock or mildly lowered Jaguar XKR-S.
Do I need wheel spacers for my Jaguar XKR-S?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Jaguar XKR-S?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.82" backspacing up front and 7.5" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Jaguar XKR-S?
Yes — the Jaguar XKR-S's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 20x9 wheels · 20 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.