Satin Gunmetal 5-Spoke Forged Wheels
Monoblock · Satin Gunmetal
2025 Ioniq 5 N (US) Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ioniq 5 N (US) wheels? This page gives the 2025 Ioniq 5 N (US) bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Ioniq 5 N (US) rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 Ioniq 5 N (US) uses a 5x114.3 bolt pattern with a 67.1 mm centre bore and M12x1.5 lug nuts. Factory wheels: 21x9.5J at ET40 (front and rear). For aftermarket wheels, 21x10.0J ET35 sits flush and 21x10.5J ET30 is the most aggressive fit.
Forged wheels for the 2025 Ioniq 5 N (US) — drilled 5x114.3 with a 67.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Ioniq 5 N (US) (2025): 5x114.3 bolt pattern, 67.1mm center bore. Factory wheels: 21x9.5J at ET40 offset (front and rear). Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore67.1mm
Wheel Load Rating748–863 kg/wheel (Standard Passenger Car segment reference)
Year2025
Category5-Lug EV Hatchback
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 25, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 21x9.5J at ET40 offset (front and rear) |
| Flush Fitment | 21x10.0J at ET35 offset |
| Maximum Aggressive | 21x10.5J at ET30 offset |
Forged Wheel Designs for the Ioniq 5 N (US)
Every design below is forged to order, so it can be machined to the Ioniq 5 N (US)'s 5x114.3 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
Hyundai N Style Matte Silver Split-Spoke Machined Face Forged Wheels
Monoblock · Matte Silver
Vossen HF-5-Style Brushed Silver 5 Y-Spoke Side-Milled Forged Wheels
Replica · Brushed Silver
OZ Racing-Style Polished Turbofan Dish Riveted Lip Forged Wheels
2-Piece · Polished
Hyundai N Style LF Black Machined 5-Spoke Y-Design Forged Wheels
Replica · Black Machined
Hyundai N Style Bright Silver 10-Spoke Forged Wheels
Replica · Bright Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a compact performance platform, every pound of rotational mass fights the car's natural agility. A forged wheel keeps strength at the factory-rated level while cutting that rotational weight, which is where the driving-feel improvement actually comes from.
The Ioniq 5 N (US) runs a 5x114.3 bolt pattern, 67.1mm center bore, and a 21x9.5J at ET40, front and rear, wheel from the factory. Our Flush Fitment reference is 21x10.0J at ET35, which tucks the tire under the fender lip on a stock-height Ioniq 5 N (US). Our Maximum Aggressive reference is 21x10.5J at ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Hyundai Ioniq 5 N (US) OE Wheel Specs
The 2025 Hyundai Ioniq 5 N (US) (EV Hatchback) uses a 5x114.3 bolt pattern with a 67.1mm center bore. Factory wheels are 21x9.5J at ET40 offset (front and rear).
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ioniq 5 N (US) (2025) we drill the 5x114.3 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 21x9.5J | ET40 | 6.82 in (173 mm) | — | — |
| Flush | 21x10J | ET35 | 6.88 in (175 mm) | +1 mm | +11 mm |
| Maximum | 21x10.5J | ET30 | 6.93 in (176 mm) | +3 mm | +23 mm |
Vehicles With the Same Hub as the Ioniq 5 N (US) (5x114.3, 67.1 mm Bore)
In our database, 456 other vehicle entries from 30 makes use exactly the same 5x114.3 bolt pattern and 67.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 35.2% of those also use a 67.1 mm center bore.
Hub-Centric Rings for a 67.1 mm Center Bore
A wheel with a center bore larger than 67.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 67.1 mm |
| 70.5 mm | 70.5 → 67.1 mm |
| 71.6 mm | 71.6 → 67.1 mm |
| 72.6 mm | 72.6 → 67.1 mm |
| 73.1 mm | 73.1 → 67.1 mm |
ANKUSI forged wheels are bored to exactly 67.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Ioniq 5 N (US) use?
The 2025 Ioniq 5 N (US) uses a 5x114.3 bolt pattern.
How many lug bolts does the Ioniq 5 N (US) use?
The Ioniq 5 N (US) uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ioniq 5 N (US)?
The Ioniq 5 N (US)'s center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ioniq 5 N (US)?
Factory wheels on the Ioniq 5 N (US) are 21x9.5J at ET40 offset (front and rear).
What is the biggest wheel size I can fit on my Ioniq 5 N (US) without rubbing?
The most aggressive fitment we recommend without fender work is 21x10.5J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ioniq 5 N (US)?
For a flush look with minimal to no rubbing, we recommend 21x10.0J at ET35 offset as a starting point on a stock or mildly lowered Ioniq 5 N (US).
Do I need wheel spacers for my Ioniq 5 N (US)?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ioniq 5 N (US)?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ioniq 5 N (US)?
The Ioniq 5 N (US) runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 21x9.5 wheels · 21 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.