2022 Hennessey VelociRaptor 400 Bronco Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Hennessey VelociRaptor 400 Bronco wheels? This page gives the 2022 Hennessey VelociRaptor 400 Bronco bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Hennessey VelociRaptor 400 Bronco rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2022 Hennessey VelociRaptor 400 Bronco uses a 6x139.7 bolt pattern with a 93.1 mm centre bore. Factory wheels: 18x9J ET30. For aftermarket wheels, 18x9.5J ET12 sits flush.
Forged wheels for the 2022 Hennessey VelociRaptor 400 Bronco — drilled 6x139.7 with a 93.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Hennessey VelociRaptor 400 Bronco (2022): 6x139.7 bolt pattern, 93.1mm center bore, OE 18x9J ET30. Forged wheel fitment specs from ANKUSI.
Bolt Pattern6x139.7
Wheel Bolt/Nut1/2\"x20 Nut
Center Bore93.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2022
Category6-Lug Off-Road (Beadlock)
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x9J ET30 |
| Flush Fitment | 18x9.5J at ET12 offset |
Forged Wheel Designs for the Hennessey VelociRaptor 400 Bronco
Every design below is forged to order, so it can be machined to the Hennessey VelociRaptor 400 Bronco's 6x139.7 bolt pattern and 93.1 mm center bore, with the width and offset calculated for your setup.
Wolf Gloss Black Exposed Bolt Detail Off-Road Forged Wheels
Off-Road · Gloss Black
Gloss Black 10-Spoke Forged Wheels
Off-Road · Matte Black
BBS Gloss Black / Red Custom Off-Road Forged Wheels
Off-Road · Gloss Black / Red
KMC Wheels Yellow Beadlock Off-Road Forged Wheels
Off-Road Beadlock · Yellow
Black / Machined Face Forged Wheels
Off-Road · Black Machined
Polished / Bronze Multi-Spoke Forged Wheels
Off-Road Beadlock · Polished / Bronze
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Off-road platforms put real, repeated impact loads through the wheel that street-only vehicles never see, so the factory strength margin on the Hennessey VelociRaptor 400 Bronco isn't a formality — it's load-bearing in a literal sense. Forging matches that margin at a lower rotational weight than an equivalent cast wheel, which matters both on the trail and on the highway miles between trailheads.
The Hennessey VelociRaptor 400 Bronco ships from the factory on a 6x139.7 bolt pattern with a 93.1mm center bore and a 18x9J ET30 wheel. Our flush reference for the Hennessey VelociRaptor 400 Bronco is 18x9.5J ET12.; our maximum aggressive reference is 20x10J ET0. — beyond that, expect clearance issues against the fender liner without further modification.
Hennessey VelociRaptor 400 Bronco OE Wheel Specs
The Hennessey VelociRaptor 400 Bronco ships from the factory on 6x139.7 bolt pattern wheels with a 93.1mm center bore. The stock wheel size is 18x9J ET30, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Hennessey VelociRaptor 400 Bronco (2022) we drill the 6x139.7 pattern and cut the centre bore to 93.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x9J | ET30 | 6.18 in (157 mm) | — | — |
| Flush | 18x9.5J | ET12 | 5.72 in (145 mm) | −12 mm | +24 mm |
| Maximum | 20x10J | ET0 | 5.50 in (140 mm) | −17 mm | +43 mm |
Vehicles With the Same Hub as the Hennessey VelociRaptor 400 Bronco (6x139.7, 93.1 mm Bore)
In our database, 30 other vehicle entries from 4 makes use exactly the same 6x139.7 bolt pattern and 93.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
6x139.7 is used by 4.0% of the vehicle pages in our English fitment guide (258 of 6,503); 12.0% of those also use a 93.1 mm center bore.
Hub-Centric Rings for a 93.1 mm Center Bore
A wheel with a center bore larger than 93.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 100.1 mm | 100.1 → 93.1 mm |
| 106.1 mm | 106.1 → 93.1 mm |
| 108.1 mm | 108.1 → 93.1 mm |
| 110.1 mm | 110.1 → 93.1 mm |
ANKUSI forged wheels are bored to exactly 93.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Hennessey VelociRaptor 400 Bronco use?
The 2022 Hennessey VelociRaptor 400 Bronco uses a 6x139.7 bolt pattern.
How many lug bolts does the Hennessey VelociRaptor 400 Bronco use?
The Hennessey VelociRaptor 400 Bronco uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Hennessey VelociRaptor 400 Bronco?
The Hennessey VelociRaptor 400 Bronco's center bore is 93.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Hennessey VelociRaptor 400 Bronco?
Factory wheels on the Hennessey VelociRaptor 400 Bronco are 18x9J ET30.
What does a flush wheel fitment look like on the Hennessey VelociRaptor 400 Bronco?
For a flush look with minimal to no rubbing, we recommend 18x9.5J at ET12 offset as a starting point on a stock or mildly lowered Hennessey VelociRaptor 400 Bronco.
Do I need wheel spacers for my Hennessey VelociRaptor 400 Bronco?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Hennessey VelociRaptor 400 Bronco?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.72" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Hennessey VelociRaptor 400 Bronco?
The Hennessey VelociRaptor 400 Bronco runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x9 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.