Gloss Black Milled Mesh Forged Wheels
Off-Road Beadlock · Gloss Black
2009 Hamann BMW X6 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Hamann BMW X6 wheels? This page gives the 2009 Hamann BMW X6 bolt pattern (5x120), centre bore, factory rim size and the offset range for aftermarket and forged Hamann BMW X6 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2009 Hamann BMW X6 uses a 5x120 bolt pattern with a 74.1 mm centre bore and M14x1.5 lug bolts. Factory wheels: 19x9J ET40. For aftermarket wheels, 22x10J ET35 sits flush.
Forged wheels for the 2009 Hamann BMW X6 — drilled 5x120 with a 74.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Hamann BMW X6 (2009): 5x120 bolt pattern, 74.1mm front / 72.6mm rear center bore, OE 19x9J ET40. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x120
Wheel Bolt/NutM14x1.5 Bolt
Center Bore74.1mm front / 72.6mm rear
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2009
Category5-Lug Large Sedan/SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x9J ET40 |
| Flush Fitment | 22x10J at ET35 offset |
Forged Wheel Designs for the Hamann BMW X6
Every design below is forged to order, so it can be machined to the Hamann BMW X6's 5x120 bolt pattern, with the width and offset calculated for your setup.
NIO ET7 Forged Wheels
Monoblock · Silver
APEX VS-5RS-Style Chrome Concave Forged Wheels
Concave · Chrome
Gloss White 2-Piece 10 Y-Spoke Deep Lip Forged Wheels
2-Piece · Gloss White
Bronze 10 Y-Spoke Forged Wheels
Monoblock · Bronze
Bright Silver 5-Spoke Forged Wheels
Monoblock · Bright Silver
Gray Petal Forged Wheels
Monoblock · Gray
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Hamann BMW X6 ships from the factory on a 5x120 bolt pattern with a 74.1mm front / 72.6mm rear center bore and a 19x9J ET40 wheel. Our flush reference for the Hamann BMW X6 is 22x10J ET35.; our maximum aggressive reference is 23x11J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
Hamann BMW X6 OE Wheel Specs
The Hamann BMW X6 ships from the factory on 5x120 bolt pattern wheels with a 74.1mm front / 72.6mm rear center bore. The stock wheel size is 19x9J ET40, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Hamann BMW X6 (2009) we drill the 5x120 pattern on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 19x9J | ET40 | 6.57 in (167 mm) | — | — |
| Flush | 22x10J | ET35 | 6.88 in (175 mm) | +8 mm | +18 mm |
| Maximum | 23x11J | ET30 | 7.18 in (182 mm) | +15 mm | +35 mm |
Vehicles With the Same Hub as the Hamann BMW X6 (5x120, 74.1 mm Bore)
In our database, 34 other vehicle entries from 3 makes use exactly the same 5x120 bolt pattern and 74.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x120 is used by 10.3% of the vehicle pages in our English fitment guide (670 of 6,503); 5.2% of those also use a 74.1 mm center bore.
Hub-Centric Rings for a 74.1 mm Center Bore
A wheel with a center bore larger than 74.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 76.1 mm | 76.1 → 74.1 mm |
| 78.1 mm | 78.1 → 74.1 mm |
| 84.1 mm | 84.1 → 74.1 mm |
| 93.1 mm | 93.1 → 74.1 mm |
ANKUSI forged wheels are bored to exactly 74.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Hamann BMW X6 use?
The 2009 Hamann BMW X6 uses a 5x120 bolt pattern.
How many lug bolts does the Hamann BMW X6 use?
The Hamann BMW X6 uses a 5-lug bolt pattern (5x120), so you need a 5-lug forged wheel to bolt straight on.
What size are the factory (stock) wheels on the Hamann BMW X6?
Factory wheels on the Hamann BMW X6 are 19x9J ET40.
What does a flush wheel fitment look like on the Hamann BMW X6?
For a flush look with minimal to no rubbing, we recommend 22x10J at ET35 offset as a starting point on a stock or mildly lowered Hamann BMW X6.
Do I need wheel spacers for my Hamann BMW X6?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Hamann BMW X6?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Hamann BMW X6?
The Hamann BMW X6 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x9 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.