CCW-Style Gloss Black Mesh 2-Piece Polished Lip Off-Road Forged Wheels
Off-Road · Gloss Black / Polished Lip
2023 Ford F-150 Rattler Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford F-150 Rattler wheels? This page gives the 2023 Ford F-150 Rattler bolt pattern (6x135), centre bore, factory rim size and the offset range for aftermarket and forged Ford F-150 Rattler rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Ford F-150 Rattler (2023): 6x135 bolt pattern, 87.1mm center bore. Factory wheels: 18x7.5J F/R. Reference fitment ranges.
Bolt Pattern6x135
Wheel Bolt/NutM14x2 Nut
Center Bore87.1mm
Wheel Load Rating1000–1400 kg/wheel (Pickup / Light Truck segment reference)
Year2023
CategoryPickup
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7.5J F/R |
| Flush Fitment | 20x9.0J at ET20 offset |
| Maximum Aggressive | 20x10.0J at ET15 offset |
Forged Wheel Designs for the Ford F-150 Rattler
Every design below is forged to order, so it can be machined to the Ford F-150 Rattler's 6x135 bolt pattern and 87.1 mm center bore, with the width and offset calculated for your setup.
Gloss Black Mesh 2-Piece Deep Lip Forged Wheels
Off-Road · Gloss Black
MMX Design Polished 5-Spoke Forged Wheels
H-Type · Polished
DT Forge Pink & Chrome Multi-Spoke Wheels
H-Type · Pink / Chrome
American Force Polished Multi-Spoke Wheels
H-Type · Polished
KG1 Forged Radar Polished Forged Wheels
H-Type · Polished
Forgiato Multi-Spoke 2-Piece Forged Wheels
Off-Road · Brushed
See all Ford F-150 wheel designs Ford OEM-Style Forged Wheels Black Rhino-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a truck platform, wheel weight sits right at the unsprung mass budget the suspension engineers already spent on payload and towing capacity. A forged wheel keeps that budget intact — same strength, less rotational inertia — instead of eating into the margin the way a cheap cast aftermarket wheel can.
The Ford F-150 Rattler runs a 6x135 bolt pattern, 87.1mm center bore, and a 18x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x9.0J ET20, which tucks the tire under the fender lip on a stock-height Ford F-150 Rattler. Our Maximum Aggressive reference is 20x10.0J ET15 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford F-150 Rattler OE Wheel Specs
The 2023 Ford F-150 Rattler (Pickup) uses a 6x135 bolt pattern with a 87.1mm center bore. Factory wheels are 18x7.5J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford F-150 Rattler (2023) we drill the 6x135 pattern and cut the centre bore to 87.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x7.5J ET44 → ~5.98″ backspacing
- Flush: 20x9.0J ET20 → ~5.79″ backspacing
- Max: 20x10.0J ET15 → ~6.09″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford F-150 Rattler? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford F-150 Rattler use?
The 2023 Ford F-150 Rattler uses a 6x135 bolt pattern.
How many lug bolts does the Ford F-150 Rattler use?
The Ford F-150 Rattler uses a 6-lug bolt pattern (6x135), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Ford F-150 Rattler?
The Ford F-150 Rattler's center bore is 87.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford F-150 Rattler?
Factory wheels on the Ford F-150 Rattler are 18x7.5J F/R.
What is the biggest wheel size I can fit on my Ford F-150 Rattler without rubbing?
The most aggressive fitment we recommend without fender work is 20x10.0J at ET15 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford F-150 Rattler?
For a flush look with minimal to no rubbing, we recommend 20x9.0J at ET20 offset as a starting point on a stock or mildly lowered Ford F-150 Rattler.
Do I need wheel spacers for my Ford F-150 Rattler?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford F-150 Rattler?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.79" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford F-150 Rattler?
The Ford F-150 Rattler runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x2.0, conical-seat lug nut.
Factory Torque Spec: 200 Nm (150 ft-lb). F-150 spec on M14x2.0 studs; confirm the exact figure for your specific model year, since Ford has revised this across generations.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.