Belak-Style Gloss Black 5-Star Red-Ring Beadlock Forged Drag Racing Wheels
Drag Racing · Custom Finish
2007 Daihatsu Terios Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Daihatsu Terios wheels? This page gives the 2007 Daihatsu Terios bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Daihatsu Terios rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2007 Daihatsu Terios uses a 5x114.3 bolt pattern with a 66.6 mm centre bore and M12x1.5 lug nuts. Factory wheels: 16x6.0J, front and rear. For aftermarket wheels, 17x7.0J ET40 sits flush and 18x7.5J ET35 is the most aggressive fit.
Forged wheels for the 2007 Daihatsu Terios — drilled 5x114.3 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Daihatsu Terios (2007): 5x114.3 bolt pattern, 66.6mm center bore. Factory wheels: 16x6.0J F/R. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore66.6mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2007
CategorySUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 16x6.0J F/R |
| Flush Fitment | 17x7.0J at ET40 offset |
| Maximum Aggressive | 18x7.5J at ET35 offset |
Forged Wheel Designs for the Daihatsu Terios
Every design below is forged to order, so it can be machined to the Daihatsu Terios's 5x114.3 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
Nismo-Style Gloss Black 5-Spoke Beadlock Forged Wheels
Off-Road Beadlock · Gloss Black
Vossen-Style Gloss Black 5 Y-Split-Spoke Forged Wheels
Replica · Gloss Black
Vossen HF-7-Style Side-Milled Transparent Gold 10 Y-Spoke Forged Wheels
Replica · Side-milled Transparent Gold
Gunmetal 15-Spoke Mesh Forged Wheels
Monoblock · Gunmetal
Rays Volk Racing TE37-Style Bronze Gold 6-Spoke Forged Wheels
Replica · Bronze Gold
Advan Racing Metallic Gray / Gray 5-Spoke Racing Forged Wheels
Replica · Metallic Gray / Gray
Belak-Style Gloss Black / Machined 5 Split-Spoke Forged Drag Racing Wheels
Drag Racing · Gloss Black / Machined
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Daihatsu Terios runs a 5x114.3 bolt pattern, 66.6mm center bore, and a 16x6.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x7.0J ET40, which tucks the tire under the fender lip on a stock-height Daihatsu Terios. Our Maximum Aggressive reference is 18x7.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Daihatsu Terios OE Wheel Specs
The 2007 Daihatsu Terios (SUV) uses a 5x114.3 bolt pattern with a 66.6mm center bore. Factory wheels are 16x6.0J F/R.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Daihatsu Terios (2007) we drill the 5x114.3 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 16x6.0J ET50 → ~5.47″ backspacing
- Flush: 17x7.0J ET40 → ~5.57″ backspacing
- Max: 18x7.5J ET35 → ~5.63″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Daihatsu spec, or want a wheel built to a custom offset for your Daihatsu Terios? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Daihatsu Terios: Specs by Model Year
| Year | Bolt pattern | Center bore | Factory wheel |
|---|---|---|---|
| 2000 | 5x114.3 | 66.6 mm | 15x5.5J |
| 2007 | 5x114.3 | 66.6 mm | 16x6J |
Bolt pattern and center bore stay the same across all 2 model years in our database (2000–2007).
Vehicles With the Same Hub as the Daihatsu Terios (5x114.3, 66.6 mm Bore)
In our database, 13 other vehicle entries from 5 makes use exactly the same 5x114.3 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 1.2% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Daihatsu Terios use?
The 2007 Daihatsu Terios uses a 5x114.3 bolt pattern.
How many lug bolts does the Daihatsu Terios use?
The Daihatsu Terios uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Daihatsu Terios?
The Daihatsu Terios's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Daihatsu Terios?
Factory wheels on the Daihatsu Terios are 16x6.0J F/R.
What is the biggest wheel size I can fit on my Daihatsu Terios without rubbing?
The most aggressive fitment we recommend without fender work is 18x7.5J at ET35 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Daihatsu Terios?
For a flush look with minimal to no rubbing, we recommend 17x7.0J at ET40 offset as a starting point on a stock or mildly lowered Daihatsu Terios.
Do I need wheel spacers for my Daihatsu Terios?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Daihatsu Terios?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.57" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Daihatsu Terios?
The Daihatsu Terios runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 16x6 wheels · 16 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.