Boyd Racing-Style Gloss Black / Mirror Milled 5-Spoke Beadlock Forged Wheels
Off-Road Beadlock · Gloss Black / Mirror Milled
2025 Ora 03 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ora 03 wheels? This page gives the 2025 Ora 03 bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Ora 03 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 Ora 03 uses a 5x114.3 bolt pattern with a 66.6 mm centre bore. For aftermarket wheels, 18x8J ET35 sits flush.
Forged wheels for the 2025 Ora 03 — drilled 5x114.3 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Ora 03 (2025) wheel fitment guide: 5x114.3 bolt pattern, 66.6mm center bore, factory 18x7J ET45 wheels. Flush and aggressive forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Center Bore66.6mm
Year2025
CategorySedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | 18x8J at ET35 offset |
Forged Wheel Designs for the Ora 03
Every design below is forged to order, so it can be machined to the Ora 03's 5x114.3 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
Matte Silver Custom Forged Wheels
Monoblock · Matte Silver
Gloss Black 5-Spoke Machined Face Forged Wheels
Monoblock · Gloss Black
HRE-Style Brushed Silver 5 Y-Spoke Forged Wheels
Monoblock · Brushed Silver
Gloss Black Machined Face Forged Wheels
Monoblock · Gloss Black
Matte Black Multi-Spoke Forged Wheels
Monoblock · Matte Black
Belak-Style Black / Milled 16-Spoke Beadlock Forged Drag Racing Wheels
Drag Racing · Black Milled
Gloss Black 5-Spoke Windowed Ring Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Ora 03 ships from the factory on a 5x114.3 bolt pattern with a 66.6mm center bore and a 18x7J ET45 wheel. Our flush reference for the Ora 03 is 18x8J ET35.; our maximum aggressive reference is 19x8J ET32. — beyond that, expect clearance issues against the fender liner without further modification.
Ora 03 OE Wheel Specs
The Ora 03 ships from the factory on 5x114.3 bolt pattern wheels with a 66.6mm center bore. The stock wheel size is 18x7J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ora 03 (2025) we drill the 5x114.3 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
- OE 18x7J ET45: backspacing ≈ 5.77"
- Flush 18x8J ET35: backspacing ≈ 5.88"
- Max 19x8J ET32: backspacing ≈ 5.76"
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Ora 03.
Vehicles With the Same Hub as the Ora 03 (5x114.3, 66.6 mm Bore)
In our database, 14 other vehicle entries from 5 makes use exactly the same 5x114.3 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 1.2% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Ora 03 use?
The 2025 Ora 03 uses a 5x114.3 bolt pattern.
How many lug bolts does the Ora 03 use?
The Ora 03 uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ora 03?
The Ora 03's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Ora 03?
For a flush look with minimal to no rubbing, we recommend 18x8J at ET35 offset as a starting point on a stock or mildly lowered Ora 03.
Do I need wheel spacers for my Ora 03?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ora 03?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ora 03?
The Ora 03 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.