2021 Ora Good Cat Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ora Good Cat wheels? This page gives the 2021 Ora Good Cat bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Ora Good Cat rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2021 Ora Good Cat uses a 5x114.3 bolt pattern with a 66.6 mm centre bore. Factory wheels: 17x6.5J ET45. For aftermarket wheels, 18x8J ET35 sits flush.
Forged wheels for the 2021 Ora Good Cat — drilled 5x114.3 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Ora Good Cat (2021): 5x114.3 bolt pattern, 66.6mm center bore, OE 17x6.5J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Center Bore66.6mm
Year2021
CategorySedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x6.5J ET45 |
| Flush Fitment | 18x8J at ET35 offset |
Forged Wheel Designs for the Ora Good Cat
Every design below is forged to order, so it can be machined to the Ora Good Cat's 5x114.3 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
Gloss Black 5-Star Red-Ring Beadlock Forged Wheels
Off-Road Beadlock · Custom Finish
Gunmetal Directional Milled Forged Wheels
Monoblock · Gunmetal
Vossen HF-5-Style Bronze Forged Wheels
Replica · Bronze
Orange Mesh Silver-Ring Beadlock Forged Wheels
Off-Road Beadlock · Orange
Rays-Style Gloss Black 5 Y-Spoke Deep Lip Forged Wheels
Deep Dish · Gloss Black
Vossen-Style Brushed Silver Multi-Spoke Turbine Forged Wheels
Replica · Matte Silver
BTS Polished Silver 5-Hole Forged Wheels
Replica · Polished Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The Ora Good Cat ships from the factory on a 5x114.3 bolt pattern with a 66.6mm center bore and a 17x6.5J ET45 wheel. Our flush reference for the Ora Good Cat is 18x8J ET35.; our maximum aggressive reference is 19x8J ET32. — beyond that, expect clearance issues against the fender liner without further modification.
Ora Good Cat OE Wheel Specs
The Ora Good Cat ships from the factory on 5x114.3 bolt pattern wheels with a 66.6mm center bore. The stock wheel size is 17x6.5J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ora Good Cat (2021) we drill the 5x114.3 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 17x6.5J | ET45 | 5.52 in (140 mm) | — | — |
| Flush | 18x8J | ET35 | 5.88 in (149 mm) | +9 mm | +29 mm |
| Maximum | 19x8J | ET32 | 5.76 in (146 mm) | +6 mm | +32 mm |
Vehicles With the Same Hub as the Ora Good Cat (5x114.3, 66.6 mm Bore)
In our database, 14 other vehicle entries from 5 makes use exactly the same 5x114.3 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 1.2% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Ora Good Cat use?
The 2021 Ora Good Cat uses a 5x114.3 bolt pattern.
How many lug bolts does the Ora Good Cat use?
The Ora Good Cat uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ora Good Cat?
The Ora Good Cat's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ora Good Cat?
Factory wheels on the Ora Good Cat are 17x6.5J ET45.
What does a flush wheel fitment look like on the Ora Good Cat?
For a flush look with minimal to no rubbing, we recommend 18x8J at ET35 offset as a starting point on a stock or mildly lowered Ora Good Cat.
Do I need wheel spacers for my Ora Good Cat?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ora Good Cat?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ora Good Cat?
The Ora Good Cat runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 17x6.5 wheels · 17 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.