Daihatsu Cuore Bolt Pattern, Center Bore & Wheel Offset (1997–2004)
Daihatsu Cuore wheel fitment: 4x100 bolt pattern, 54.1mm center bore; 4x110 bolt pattern, 66.1mm center bore.
- 4x100bolt pattern (PCD), most common
- 54.1 mmcenter bore
- M12x1.5 Nutwheel bolt / nut
- 2 guidesmodel years 1997–2004
Bolt pattern by generation
- 4x100, 54.1 mm center bore — 2004 (1 variants)
- 4x110, 66.1 mm center bore — 1997 (1 variants)
Daihatsu Cuore wheel specs by year and trim
| Year | Model / trim | Bolt pattern | Center bore | OE wheel |
|---|---|---|---|---|
| 2004 | Daihatsu Cuore | 4x100 | 54.1 mm | 13x4.5J |
| 1997 | Daihatsu Cuore | 4x110 | 66.1 mm | 12x4.0J |
Factory wheel sizes on the Daihatsu Cuore
Across the 2 Daihatsu Cuore trims with a documented factory wheel, the OE diameter is 12-13 inch, width 4-4.5J. A forged wheel that keeps the bolt pattern and hub bore of your generation (see the table above) and matches the factory offset listed on the model page bolts on without spacers or hub rings. Going one inch up in diameter with a lower-profile tyre keeps the rolling circumference inside the usual 1.5% tolerance; every extra 0.5J of width moves the outer lip about 6 mm outward at the same offset, and each 5 mm less offset moves the whole wheel 5 mm outward.
Vehicles With the Same Hub as the Daihatsu Cuore (4x100, 54.1 mm Bore)
In our database, 145 other vehicle entries from 22 makes use exactly the same 4x100 bolt pattern and 54.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
4x100 is used by 6.9% of the vehicle pages in our English fitment guide (451 of 6,503); 34.4% of those also use a 54.1 mm center bore.
Hub-Centric Rings for a 54.1 mm Center Bore
A wheel with a center bore larger than 54.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 56.1 mm | 56.1 → 54.1 mm |
| 57.1 mm | 57.1 → 54.1 mm |
| 60.1 mm | 60.1 → 54.1 mm |
| 63.4 mm | 63.4 → 54.1 mm |
| 73.1 mm | 73.1 → 54.1 mm |
ANKUSI forged wheels are bored to exactly 54.1 mm for this vehicle, so no ring is needed.
Sources and Last Update
Bolt pattern and center bore were checked against at least two independent fitment references before publication.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
FAQ
What is the bolt pattern on a Daihatsu Cuore?
The Daihatsu Cuore uses a 4x100 bolt pattern on most variants we cover with a 54.1mm center bore. Other generations use 4x110 / 66.1mm (1997–1997). Always check the exact year and trim before ordering.
What is the Daihatsu Cuore center bore?
The hub-centric center bore is 54.1 mm on the most common generation; see the table for variants. Aftermarket wheels should match this bore or use hub-centric rings so the hub, not the bolts, carries the load.
Do all Daihatsu Cuore years share the same wheel fitment?
No. The bolt pattern or center bore changed between generations, so wheels are not interchangeable across all years. Use the year-by-year table on this page to pick the right specification.
Which forged wheels fit the Daihatsu Cuore?
Any wheel drilled 4x100 with a 54.1mm hub bore in the offset range shown on the model guide. ANKUSI forges wheels to order for this exact specification, in 14–24 inch diameters, so no adapters or hub rings are needed.