Vossen-Style Matte Silver 5-Spoke Forged Wheels
Monoblock · Matte Silver
2025 Audi SQ6 e-tron (US) Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Audi SQ6 e-tron (US) wheels? This page gives the 2025 Audi SQ6 e-tron (US) bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Audi SQ6 e-tron (US) rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 Audi SQ6 e-tron (US) uses a 5x130 bolt pattern with a 66.5 mm centre bore and M14x1.5 lug bolts. For aftermarket wheels, 21x9.5J ET25 front / 21x10.5J ET30 rear sits flush.
Forged wheels for the 2025 Audi SQ6 e-tron (US) — drilled 5x130 with a 66.5 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Audi SQ6 e-tron (US) (2025): 5x130 bolt pattern, 66.5mm center bore, OE F 20x9J ET35 / R 20x10J ET40. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore66.5mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2025
Category5-Lug Large Sedan/SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 21x9.5J ET25 / R 21x10.5J ET30 |
Forged Wheel Designs for the Audi SQ6 e-tron (US)
Every design below is forged to order, so it can be machined to the Audi SQ6 e-tron (US)'s 5x130 bolt pattern and 66.5 mm center bore, with the width and offset calculated for your setup.
Gloss Black Mesh 2-Piece Polished Deep Lip Forged Wheels
2-Piece · Gloss Black
Gloss White 10 Y-Spoke Forged Wheels
Monoblock · Gloss White
HRE-Style Mirror Polished 10-Spoke 2-Piece Riveted Forged Wheels
2-Piece · Mirror Polished
Forgiato-Style Mirror Polished Multi-Spoke Mesh 2-Piece Forged Wheels
2-Piece · Mirror Polished
Forgiato-Style Mirror Polished Twin-Blade 5-Spoke 2-Piece Forged Wheels
2-Piece · Mirror Polished
Transparent Gold Petal-Spoke Forged Wheels
Monoblock · Transparent Gold
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Audi SQ6 e-tron (US) ships from the factory on a 5x130 bolt pattern with a 66.5mm center bore and a F 20x9J ET35 / R 20x10J ET40 wheel. Our flush reference for the Audi SQ6 e-tron (US) is F 21x9.5J ET25 / R 21x10.5J ET30.; our maximum aggressive reference is F 22x10J ET20 / R 22x11J ET25. — beyond that, expect clearance issues against the fender liner without further modification.
Audi SQ6 e-tron (US) OE Wheel Specs
The Audi SQ6 e-tron (US) ships from the factory on 5x130 bolt pattern wheels with a 66.5mm center bore. The stock wheel size is F 20x9J ET35 / R 20x10J ET40, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Audi SQ6 e-tron (US) (2025) we drill the 5x130 pattern and cut the centre bore to 66.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 20x9J | ET35 | 6.38 in (162 mm) | — | — |
| Flush | 21x9.5J | ET25 | 6.23 in (158 mm) | −4 mm | +16 mm |
| Maximum | 22x10J | ET20 | 6.29 in (160 mm) | −2 mm | +28 mm |
Vehicles With the Same Hub as the Audi SQ6 e-tron (US) (5x130, 66.5 mm Bore)
In our database, 11 other vehicle entries from 2 makes use exactly the same 5x130 bolt pattern and 66.5 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x130 is used by 5.8% of the vehicle pages in our English fitment guide (375 of 6,503); 3.2% of those also use a 66.5 mm center bore.
Hub-Centric Rings for a 66.5 mm Center Bore
A wheel with a center bore larger than 66.5 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.6 mm | 66.6 → 66.5 mm |
| 67.1 mm | 67.1 → 66.5 mm |
| 70.1 mm | 70.1 → 66.5 mm |
| 70.5 mm | 70.5 → 66.5 mm |
| 73.1 mm | 73.1 → 66.5 mm |
ANKUSI forged wheels are bored to exactly 66.5 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Audi SQ6 e-tron (US) use?
The 2025 Audi SQ6 e-tron (US) uses a 5x130 bolt pattern.
How many lug bolts does the Audi SQ6 e-tron (US) use?
The Audi SQ6 e-tron (US) uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Audi SQ6 e-tron (US)?
The Audi SQ6 e-tron (US)'s center bore is 66.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Audi SQ6 e-tron (US)?
For a flush look with minimal to no rubbing, we recommend F 21x9.5J ET25 / R 21x10.5J ET30 as a starting point on a stock or mildly lowered Audi SQ6 e-tron (US).
Do I need wheel spacers for my Audi SQ6 e-tron (US)?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Audi SQ6 e-tron (US)?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.23" backspacing up front and 6.93" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Audi SQ6 e-tron (US)?
Yes — the Audi SQ6 e-tron (US)'s factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.5, ball-seat lug bolt (13mm radius).
Factory Torque Spec: 120 Nm (89 ft-lb). Shared VW/Audi Group ball-seat bolt spec used across most 5x112 Audi models.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 20x9 wheels · 20 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.