Aston Martin DB11 Lightning Sliver (2017) Wheel Fitment
Aston Martin DB11 Lightning Sliver (2017): 5x128 bolt pattern, 75.1mm center bore. Factory wheels: F: 20x9.0J R: 20x11.0J. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 20x9.0J R: 20x11.0J |
| Flush Fitment | F 21x9.5J ET32 / R 21x11.0J ET40 |
| Maximum Aggressive | F 22x10.0J ET28 / R 22x11.5J ET35 |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a supercar, wheel weight is one of the few remaining places to cut rotational mass without touching the powertrain or chassis the factory already optimized. Forging gets there at the same structural margin as the OE wheel, which is exactly the trade a car built around outright performance rewards.
The Aston Martin DB11 Lightning Sliver runs a 5x128 bolt pattern, 75.1mm center bore, and a F: 20x9.0J wheel from the factory. Our Flush Fitment reference is F 21x9.5J ET32 / R 21x11.0J ET40, which tucks the tire under the fender lip on a stock-height Aston Martin DB11 Lightning Sliver. Our Maximum Aggressive reference is F 22x10.0J ET28 / R 22x11.5J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Aston Martin DB11 Lightning Sliver OE Wheel Specs
The 2017 Aston Martin DB11 Lightning Sliver (Luxury Grand Tourer) uses a 5x128 bolt pattern with a 75.1mm center bore. Factory wheels are F: 20x9.0J R: 20x11.0J.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
Flush Fitment
For a flush look with minimal rubbing, F 21x9.5J ET32 / R 21x11.0J ET40 is the recommended starting point on a stock or mildly lowered Aston Martin DB11 Lightning Sliver.
Maximum Aggressive Fitment
F 22x10.0J ET28 / R 22x11.5J ET35 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style F 20x9.0J ET40 / R 20x11.0J ET48
Recommended setup: F 20x9.0J ET40 / R 20x11.0J ET48 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade F 21x9.5J ET36 / R 21x11.0J ET44
Recommended setup: F 21x9.5J ET36 / R 21x11.0J ET44 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit F 21x9.5J ET32 / R 21x11.0J ET40
Recommended setup: F 21x9.5J ET32 / R 21x11.0J ET40 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive F 22x10.0J ET30 / R 22x11.5J ET38
Recommended setup: F 22x10.0J ET30 / R 22x11.5J ET38 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive F 22x10.0J ET28 / R 22x11.5J ET35
Recommended setup: F 22x10.0J ET28 / R 22x11.5J ET35 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | F 20x9.0J ET40 / R 20x11.0J ET48 | F 21x9.5J ET36 / R 21x11.0J ET44 | F 21x9.5J ET32 / R 21x11.0J ET40 | F 22x10.0J ET30 / R 22x11.5J ET38 | F 22x10.0J ET28 / R 22x11.5J ET35 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: F 20x9.0J ET40 / R 20x11.0J ET48
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: F 21x9.5J ET32 / R 21x11.0J ET40
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: F 22x10.0J ET28 / R 22x11.5J ET35
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 20x9.0J ET40 → ~6.57″ F backspacing, R 20x11.0J ET48 → ~7.89″ R backspacing
- Flush: F 21x9.5J ET32 → ~6.51″ F backspacing, R 21x11.0J ET40 → ~7.57″ R backspacing
- Max: F 22x10.0J ET28 → ~6.6″ F backspacing, R 22x11.5J ET35 → ~7.63″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Aston Martin spec, or want a wheel built to a custom offset for your Aston Martin DB11 Lightning Sliver? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.