2006 Spyker C8 Laviolette Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Spyker C8 Laviolette wheels? This page gives the 2006 Spyker C8 Laviolette bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Spyker C8 Laviolette rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2006 Spyker C8 Laviolette uses a 5x112 bolt pattern with a 57.1 mm centre bore. For aftermarket wheels, 19x9J ET30 front / 19x10J ET30 rear sits flush.
Forged wheels for the 2006 Spyker C8 Laviolette — drilled 5x112 with a 57.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Spyker C8 Laviolette (2006): 5x112 bolt pattern, 57.1mm center bore, OE F 18x8.5J ET35 / R 18x9.5J ET35. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x112
Center Bore57.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2006
Category5-Lug Supercar (2-Piece)
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 19x9J ET30 / R 19x10J ET30 |
Forged Wheel Designs for the Spyker C8 Laviolette
Every design below is forged to order, so it can be machined to the Spyker C8 Laviolette's 5x112 bolt pattern and 57.1 mm center bore, with the width and offset calculated for your setup.
BBS-Style 2-Piece Black Chrome Mesh Red Cap Polished Lip Forged Wheels
2-Piece · Black Chrome
WF Gloss Black 10-Spoke Forged Wheels
Replica · Gloss Black
Gloss Black Multi-Spoke Turbine Forged Wheels
Monoblock · Gloss Black
Advan-Style Metallic Gray 5-Spoke Forged Wheels
Monoblock · Metallic Gray
BR Wheels-Style Mirror Polished Directional 5-Spoke 2-Piece Forged Wheels
2-Piece · Mirror Polished
Brushed Bright Silver 10 Y-Spoke Forged Wheels
Monoblock · Brushed Bright Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a supercar, wheel weight is one of the few remaining places to cut rotational mass without touching the powertrain or chassis the factory already optimized. Forging gets there at the same structural margin as the OE wheel, which is exactly the trade a car built around outright performance rewards.
The Spyker C8 Laviolette ships from the factory on a 5x112 bolt pattern with a 57.1mm center bore and a F 18x8.5J ET35 / R 18x9.5J ET35 wheel. Our flush reference for the Spyker C8 Laviolette is F 19x9J ET30 / R 19x10J ET30.; our maximum aggressive reference is F 19x9.5J ET25 / R 19x10.5J ET25. — beyond that, expect clearance issues against the fender liner without further modification.
Spyker C8 Laviolette OE Wheel Specs
The Spyker C8 Laviolette ships from the factory on 5x112 bolt pattern wheels with a 57.1mm center bore. The stock wheel size is F 18x8.5J ET35 / R 18x9.5J ET35, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Spyker C8 Laviolette (2006) we drill the 5x112 pattern and cut the centre bore to 57.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x8.5J | ET35 | 6.13 in (156 mm) | — | — |
| Flush | 19x9J | ET30 | 6.18 in (157 mm) | +1 mm | +11 mm |
| Maximum | 19x9.5J | ET25 | 6.23 in (158 mm) | +3 mm | +23 mm |
Vehicles With the Same Hub as the Spyker C8 Laviolette (5x112, 57.1 mm Bore)
In our database, 407 other vehicle entries from 18 makes use exactly the same 5x112 bolt pattern and 57.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 29.0% of those also use a 57.1 mm center bore.
Hub-Centric Rings for a 57.1 mm Center Bore
A wheel with a center bore larger than 57.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 57.1 mm |
| 63.4 mm | 63.4 → 57.1 mm |
| 64.1 mm | 64.1 → 57.1 mm |
| 65.1 mm | 65.1 → 57.1 mm |
| 73.1 mm | 73.1 → 57.1 mm |
ANKUSI forged wheels are bored to exactly 57.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Spyker C8 Laviolette use?
The 2006 Spyker C8 Laviolette uses a 5x112 bolt pattern.
How many lug bolts does the Spyker C8 Laviolette use?
The Spyker C8 Laviolette uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Spyker C8 Laviolette?
The Spyker C8 Laviolette's center bore is 57.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Spyker C8 Laviolette?
For a flush look with minimal to no rubbing, we recommend F 19x9J ET30 / R 19x10J ET30 as a starting point on a stock or mildly lowered Spyker C8 Laviolette.
Do I need wheel spacers for my Spyker C8 Laviolette?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Spyker C8 Laviolette?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.18" backspacing up front and 6.68" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Spyker C8 Laviolette?
Yes — the Spyker C8 Laviolette's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8.5 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Bolt pattern and center bore on this page come from published fitment references and are still awaiting a second independent check. Last reviewed 2026-09-18. Spotted an error? Email info@ankusi.com and we will verify and correct it.