Skoda Superb iV (2020) Wheel Fitment

Skoda Superb iV (2020): 5x112 bolt pattern, 57.1mm center bore, OE 18x8J ET44. Forged wheel fitment specs from ANKUSI.

Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore57.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2020
Category5-Lug Standard Sedan

Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →

Wheel Size & Offset at a Glance

Skoda Superb iV wheel size and offset comparison by configuration
ConfigurationWheel Size & Offset
Flush Fitment19x8.5J at ET38 offset

How to Read Wheel Offset & Measurements

Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.

Diagram showing wheel measurement points: centerline, center bore diameter, PCD, offset, rim width and diameter
Centerline, center bore, PCD, offset, width & diameter
Diagram comparing positive, zero, and negative wheel offset relative to the wheel centerline
Positive vs. zero vs. negative offset

ANKUSI Engineering Expert Advice

Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.

The Skoda Superb iV ships from the factory on a 5x112 bolt pattern with a 57.1mm center bore and a 18x8J ET44 wheel. Our flush reference for the Skoda Superb iV is 19x8.5J ET38.; our maximum aggressive reference is 20x8.5J ET35. — beyond that, expect clearance issues against the fender liner without further modification.

Skoda Superb iV OE Wheel Specs

The Skoda Superb iV ships from the factory on 5x112 bolt pattern wheels with a 57.1mm center bore. The stock wheel size is 18x8J ET44, offering a balanced ride that suits most owners without any rubbing or clearance concerns.

Why the factory spec works for most owners:

  • Balances ride comfort with steering response and highway efficiency.
  • Wide tire and wheel availability at the factory diameter keeps replacement costs low.
  • Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
  • Guaranteed clearance against brake calipers and suspension components.

Flush Fitment

For a flush look without any body modification, most Skoda Superb iV owners run 19x8.5J ET38. This setup tucks the wheel face closer to the fender lip while staying within safe load and clearance limits.

Maximum Aggressive Fitment

Owners chasing a more aggressive stance push to 20x8.5J ET35. Eibach Pro-Kit PHEV springs; 19x8.5J ET38 BBS SR wheels; regenerative brakes; Michelin Pilot Sport 4 235/40 R19 tires. Note: Plug-in hybrid (1.4 TSI + electric motor). Clearance should be verified before ordering, especially on lowered cars.

5-Tier Configuration Options

A – Factory-Style: 18x8J ET44

Recommended setup: Factory-matched forged replacement

Economy impact: None

Best for: Daily drivers, warranty-conscious owners

Appearance 5/10 | Comfort 10/10 | Install difficulty ★☆☆☆

Estimated cost range: $$ (OE replacement)

B – Comfortable Upgrade: 18.5x8.5J ET41

Recommended setup: Direct bolt-on, factory suspension

Economy impact: Minimal

Best for: Owners who want a mild upgrade with no compromise

Appearance 6/10 | Comfort 9/10 | Install difficulty ★☆☆☆

Estimated cost range: $$ - $$$

C – Balanced / Flush Fit: 19x8.5J ET38

Recommended setup: Flush forged wheels, stock or mild lowering

Economy impact: Slight increase

Best for: Enthusiasts wanting a flush look daily

Appearance 8/10 | Comfort 7/10 | Install difficulty ★★☆☆

Estimated cost range: $$$

D – Aggressive: 19.5x8.5J ET37

Recommended setup: Wider forged wheels, coilovers or lowering springs

Economy impact: Noticeable increase

Best for: Show-and-drive builds

Appearance 9/10 | Comfort 5/10 | Install difficulty ★★★☆

Estimated cost range: $$$$

E – Max Aggressive: 20x8.5J ET35

Recommended setup: Eibach Pro-Kit PHEV springs; 19x8.5J ET38 BBS SR wheels; regenerative brakes; Michelin Pilot Sport 4 235/40 R19 tires. Note: Plug-in hybrid (1.4 TSI + electric motor).

Economy impact: Significant increase

Best for: Show builds, weekend cars

Appearance 10/10 | Comfort 3/10 | Install difficulty ★★★★

Estimated cost range: $$$$$

Performance Comparison Matrix

Wheel SpecTier ATier BTier CTier DTier E
Wheel Spec18x8J ET4418.5x8.5J ET4119x8.5J ET3819.5x8.5J ET3720x8.5J ET35
Economy ImpactNoneMinimalSlight increaseNoticeable increaseSignificant increase
Appearance5/106/108/109/1010/10
Comfort10/109/107/105/103/10
Install Difficulty★☆☆☆★☆☆☆★★☆☆★★★☆★★★★
Cost Range$$ (OE replacement)$$ - $$$$$$$$$$$$$$$
Best ForDaily drivers, warranty-conscious ownersOwners who want a mild upgrade with no compromiseEnthusiasts wanting a flush look dailyShow-and-drive buildsShow builds, weekend cars

Real-World Reference Cases

The following builds are compiled from typical ANKUSI customer configurations for this platform and are illustrative, not individually verified real-world builds.

Case 1: Daily Driver (Factory-Style)

Profile: Commuter prioritizing comfort and reliability.

Setup: 18x8J ET44 forged wheels, factory suspension.

Cost: $$ (OE replacement)

Outcome: No clearance issues, factory ride quality retained.

Case 2: Balanced Enthusiast (Balanced / Flush Fit)

Profile: Weekend driver wanting a flush stance without sacrificing daily usability.

Setup: 19x8.5J ET38 forged wheels, mild lowering springs.

Cost: $$$

Outcome: Flush fitment with acceptable ride comfort for daily use.

Case 3: Show Build (Max Aggressive)

Profile: Show-and-shine build prioritizing stance over comfort.

Setup: 20x8.5J ET35 forged wheels. Eibach Pro-Kit PHEV springs; 19x8.5J ET38 BBS SR wheels; regenerative brakes; Michelin Pilot Sport 4 235/40 R19 tires. Note: Plug-in hybrid (1.4 TSI + electric motor).

Cost: $$$$$

Outcome: Maximum aggressive stance; clearance verified case-by-case.

Decision Guide

1. What is this car mainly used for? Daily driving favors Tier A or B; weekend/show use favors Tier D or E.
2. What is your budget? Tiers A-B keep cost low; Tiers D-E cost significantly more in wheels, tires, and possible suspension work.
3. Is fuel economy and ride comfort a priority? If yes, stay at Tier A or B; heavier, wider wheels at Tier D-E reduce efficiency and comfort.
4. Still unsure? Tier C (Balanced / Flush Fit) is the safe default for most Skoda Superb iV owners.

Offset & Backspacing Reference

Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.

  • OE 18x8J ET44: backspacing ≈ 6.23"
  • Flush 19x8.5J ET38: backspacing ≈ 6.25"
  • Max 20x8.5J ET35: backspacing ≈ 6.13"

Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Skoda Superb iV.

Frequently Asked Questions

What bolt pattern (PCD) does the Skoda Superb iV use?
The 2020 Skoda Superb iV uses a 5x112 bolt pattern.
How many lug bolts does the Skoda Superb iV use?
The Skoda Superb iV uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What does a flush wheel fitment look like on the Skoda Superb iV?
For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET38 offset as a starting point on a stock or mildly lowered Skoda Superb iV.
Do I need wheel spacers for my Skoda Superb iV?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Skoda Superb iV?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.25" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Skoda Superb iV?
The Skoda Superb iV runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.

← Back to the full Fitment Guide · Browse forged wheels

Contact WhatsApp Get a Quote