Rolls-Royce Wheel Fitment Guide

69 fitment guides for Rolls-Royce, covering 2002 to 2025, spanning 5x112 and 5x120 bolt patterns. Browse the full list below, then open a model for bolt pattern, center bore, OE offset, flush and max wheel sizes, and offset/backspacing conversions.

Run a Rolls-Royce club, forum or blog? Add our free bolt pattern and center bore lookup to your site, set to open on Rolls-Royce only. Get the free embed code →

Rolls-Royce models: bolt pattern by model

CullinanDawnGhostPhantomSpectreWraith

Rolls-Royce Bolt Pattern & Center Bore Notes

Based on the 69 Rolls-Royce fitment guides we cover, we have documented 3 distinct bolt pattern / center bore combinations across different Rolls-Royce platforms and model years:

  • 5x120 bolt pattern, 72.6mm center bore — 46 models we cover, spanning 2002–2023.
  • 5x112 bolt pattern, 66.6mm center bore — 20 models we cover, spanning 2017–2025.
  • 5x120 bolt pattern, 66.6mm center bore — 3 models we cover, spanning 2023–2025.

Do not mix platforms: a wheel forged for one Rolls-Royce bolt pattern / center bore combination will not hub-center correctly on a different one, even if the diameter looks right. Always confirm your exact model and year against the bolt pattern and center bore listed on that model page below before ordering — or send us your VIN or trim level and we will confirm it for you.

Offset and backspacing recommendations vary by trim even within the same bolt pattern, mainly due to differences in brake caliper size and suspension geometry between base and performance trims. Every ANKUSI wheel is forged to your exact target offset, so send us your Rolls-Royce model, year, and trim and we will confirm the correct spec before production — no guessing required.

How to check the bolt pattern on your Rolls-Royce

The most common Rolls-Royce fitment in our guide is 5x120 with a 72.6 mm center bore (46 of 69 model years we cover).

  1. Read the stamping on the back of an original wheel: size, offset (ET) and bolt pattern are usually cast into a spoke or the hub pad.
  2. No stamping? Measure center-to-center between two adjacent lug holes. For 5x120 that distance is 70.5 mm (PCD × sin(180° / 5)). A 2 mm difference already means a different bolt pattern.
  3. Match generation and year on the model pages below — the same nameplate can change bolt pattern or center bore between generations.

Changing width or offset? Check how far the wheel moves in or out with our offset & backspacing calculator.

5x120 / 72.6mm center bore

Forged Wheels for Rolls-Royce

Forged-to-order wheel designs matched to Rolls-Royce bolt patterns. Every set is machined to your exact model, offset and center bore.

Vehicles Using 5x120 With a 72.6 mm Center Bore

In our database, 333 other vehicle entries from 9 makes use exactly the same 5x120 bolt pattern and 72.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.

5x120 is used by 10.3% of the vehicle pages in our English fitment guide (670 of 6,503); 50.6% of those also use a 72.6 mm center bore.

Hub-Centric Rings for a 72.6 mm Center Bore

A wheel with a center bore larger than 72.6 mm needs a hub-centric ring. The most common combinations:

Wheel boreRing size
73.1 mm73.1 → 72.6 mm
74.1 mm74.1 → 72.6 mm
76.1 mm76.1 → 72.6 mm
78.1 mm78.1 → 72.6 mm

ANKUSI forged wheels are bored to exactly 72.6 mm for this vehicle, so no ring is needed.

Sources and Last Update

Bolt pattern and center bore were checked against at least two independent fitment references before publication.

This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).

Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.

← Back to the full Fitment Guide · Browse forged wheels

Contact WhatsApp Get a Quote