Nissan Xterra Bolt Pattern, Center Bore & Wheel Offset (2003–2009)

Nissan Xterra wheel fitment: 6x114.3 bolt pattern, 66.1mm center bore (2005–2009); 6x139.7 bolt pattern, 100.1mm center bore.

  • 6x114.3bolt pattern (PCD), most common
  • 66.1 mmcenter bore
  • M12x1.25 Nutwheel bolt / nut
  • 3 guidesmodel years 2003–2009

Bolt pattern by generation

  • 6x114.3, 66.1 mm center bore — 2005–2009 (2 variants)
  • 6x139.7, 100.1 mm center bore — 2003 (1 variants)

Nissan Xterra wheel specs by year and trim

YearModel / trimBolt patternCenter boreOE wheel
2009Nissan Xterra6x114.366.1 mm16x7.0J
2005Nissan Xterra6x114.366.1 mm16x7.0J
2003Nissan Xterra6x139.7100.1 mm15x7.0J

Factory wheel sizes on the Nissan Xterra

Across the 3 Nissan Xterra trims with a documented factory wheel, the OE diameter is 15-16 inch, width 7J. A forged wheel that keeps the bolt pattern and hub bore of your generation (see the table above) and matches the factory offset listed on the model page bolts on without spacers or hub rings. Going one inch up in diameter with a lower-profile tyre keeps the rolling circumference inside the usual 1.5% tolerance; every extra 0.5J of width moves the outer lip about 6 mm outward at the same offset, and each 5 mm less offset moves the whole wheel 5 mm outward.

Vehicles With the Same Hub as the Nissan Xterra (6x114.3, 66.1 mm Bore)

In our database, 4 other vehicle entries from 3 makes use exactly the same 6x114.3 bolt pattern and 66.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.

6x114.3 is used by 0.5% of the vehicle pages in our English fitment guide (30 of 6,503); 53.3% of those also use a 66.1 mm center bore.

Offset and Backspacing: Factory Wheel vs Options

Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.

SetupSizeETBackspacingInward vs OEOutward vs OE
Factory (OE)16x7JET305.18 in (132 mm)——
Flush16x8JET155.09 in (129 mm)−2 mm+28 mm
Maximum17x8.5JET04.75 in (121 mm)−11 mm+49 mm

Hub-Centric Rings for a 66.1 mm Center Bore

A wheel with a center bore larger than 66.1 mm needs a hub-centric ring. The most common combinations:

Wheel boreRing size
66.6 mm66.6 → 66.1 mm
67.1 mm67.1 → 66.1 mm
70.1 mm70.1 → 66.1 mm
70.5 mm70.5 → 66.1 mm
73.1 mm73.1 → 66.1 mm

ANKUSI forged wheels are bored to exactly 66.1 mm for this vehicle, so no ring is needed.

Sources and Last Update

Bolt pattern and center bore were checked against at least two independent fitment references before publication.

This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).

Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.

FAQ

What is the bolt pattern on a Nissan Xterra?

The Nissan Xterra uses a 6x114.3 bolt pattern on most variants we cover with a 66.1mm center bore. Other generations use 6x139.7 / 100.1mm (2003–2003). Always check the exact year and trim before ordering.

What is the Nissan Xterra center bore?

The hub-centric center bore is 66.1 mm on the most common generation; see the table for variants. Aftermarket wheels should match this bore or use hub-centric rings so the hub, not the bolts, carries the load.

Do all Nissan Xterra years share the same wheel fitment?

No. The bolt pattern or center bore changed between generations, so wheels are not interchangeable across all years. Use the year-by-year table on this page to pick the right specification.

Which forged wheels fit the Nissan Xterra?

Any wheel drilled 6x114.3 with a 66.1mm hub bore in the offset range shown on the model guide. ANKUSI forges wheels to order for this exact specification, in 14–24 inch diameters, so no adapters or hub rings are needed.

Contact WhatsApp Get a Quote