Skoda OEM-Style Gloss Black Machined Face Forged Wheels
Monoblock · Gloss Black
2022 Skoda Karoq Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Skoda Karoq wheels? This page gives the 2022 Skoda Karoq bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Skoda Karoq rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2022 Skoda Karoq uses a 5x112 bolt pattern with a 57.1 mm centre bore and M14x1.5 lug bolts. Factory wheels: 18x7J ET45. For aftermarket wheels, 19x8J ET35 sits flush.
Forged wheels for the 2022 Skoda Karoq — drilled 5x112 with a 57.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Skoda Karoq (2022): 5x112 bolt pattern, 57.1mm center bore, OE 18x7J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore57.1mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2022
Category5-Lug Large Sedan/SUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7J ET45 |
| Flush Fitment | 19x8J at ET35 offset |
Forged Wheel Designs for the Skoda Karoq
Every design below is forged to order, so it can be machined to the Skoda Karoq's 5x112 bolt pattern and 57.1 mm center bore, with the width and offset calculated for your setup.
Skoda OEM-Style Black / Machined 5 V-Spoke Machined Face Forged Wheels
Monoblock · Black Machined
Audi RS5 Sedan Forged Wheels
Monoblock
HRE Performance P200-Style Silver Mesh Forged Wheels
Replica · Silver
Black / Silver Turbine Forged Wheels
Monoblock · Black / Silver
Gloss Black Slotted Dish Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Skoda Karoq ships from the factory on a 5x112 bolt pattern with a 57.1mm center bore and a 18x7J ET45 wheel. Our flush reference for the Skoda Karoq is 19x8J ET35.; our maximum aggressive reference is 20x8.5J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
Skoda Karoq OE Wheel Specs
The Skoda Karoq ships from the factory on 5x112 bolt pattern wheels with a 57.1mm center bore. The stock wheel size is 18x7J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Skoda Karoq (2022) we drill the 5x112 pattern and cut the centre bore to 57.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x7J | ET45 | 5.77 in (147 mm) | — | — |
| Flush | 19x8J | ET35 | 5.88 in (149 mm) | +3 mm | +23 mm |
| Maximum | 20x8.5J | ET30 | 5.93 in (151 mm) | +4 mm | +34 mm |
Vehicles With the Same Hub as the Skoda Karoq (5x112, 57.1 mm Bore)
In our database, 407 other vehicle entries from 18 makes use exactly the same 5x112 bolt pattern and 57.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 29.0% of those also use a 57.1 mm center bore.
Hub-Centric Rings for a 57.1 mm Center Bore
A wheel with a center bore larger than 57.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 57.1 mm |
| 63.4 mm | 63.4 → 57.1 mm |
| 64.1 mm | 64.1 → 57.1 mm |
| 65.1 mm | 65.1 → 57.1 mm |
| 73.1 mm | 73.1 → 57.1 mm |
ANKUSI forged wheels are bored to exactly 57.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Skoda Karoq use?
The 2022 Skoda Karoq uses a 5x112 bolt pattern.
How many lug bolts does the Skoda Karoq use?
The Skoda Karoq uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Skoda Karoq?
The Skoda Karoq's center bore is 57.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Skoda Karoq?
Factory wheels on the Skoda Karoq are 18x7J ET45.
What does a flush wheel fitment look like on the Skoda Karoq?
For a flush look with minimal to no rubbing, we recommend 19x8J at ET35 offset as a starting point on a stock or mildly lowered Skoda Karoq.
Do I need wheel spacers for my Skoda Karoq?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Skoda Karoq?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Skoda Karoq?
The Skoda Karoq runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x7 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.